. In. 46 NWhich step of the following steps is for useof a manometric tubes to measure the* differential pressureobserve that the water level in theses twotubes coincides with the level in the watertankfill the viscometer with the test liquidwhose viscosity is going to be determinedchange the slope of the tube to 10degrees. record the value of the water levelconnect the pump to the upper plug of thetank with the non - return valve in thecorrect direction and pressurize the tankuse the gauge in such away that the pointof the hook indicates the correct waterlevel in the tank.disassemble the piston and determineaccurately its weightconnect the manual pump to one of theupper values of the u tubefill the bucket with water and record itsweightprepare scale to measure between 0 and0.25 kgcover the piston with Vaseline for a bestoperationWhich step of the following steps is for use

Name: . In. 46 NWhich step of the following steps is for useof a manometric
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: . In. 46 NWhich step of the following steps is for useof a manometric tubes to measure the* differential pressureobserve that the water level in theses twotubes coincides with the level in the watertankfill the viscometer with the test liquidwhose v

Given: Which step of the following steps is for use of manometric tubes to measure the differential…

Answered: Which step of the following steps is…

Engineering

Mechanical Engineering

Which step of the following steps is for use of a manometric tubes to measure the * differential pressure observe that the water level in theses two noid with tho louol Jovel in th

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The device in Fig. is called a cone-plate viscometer. The angle of the cone is very small, so that sin θ ≈ θ ,and the gap is fi lled with the test liquid. The torque M torotate the cone at a rate V is measured. Assuming a linearvelocity profi le in the fl uid fi lm, derive an expression forfl uid viscosity μ as a function of ( M , R , V , θ ).
For liquid viscosity measurement, it is desired to create a viscometer consisting of two 30 cm long concentric cylinders. The diameter of the inner cylinder is 20 cm and the diameter of the outer cylinder is 20.2 cm. Since a torque of 0.13 N cinsm is required to rotate the inner cylinder with an angular velocity of 40 rad / s, what will be the viscosity of the fluid in the viscometer in Pa⋅s? Take the value of as 3.
A rotating viscometer consists of two concentric cylinders—a stationary inner cyliner of radius Ri and an outer cylinder of inside radius Ro rotating at angular velocity (rotation rate) ?o. In the tiny gap between the two cylinders is the fluid whose viscosity (? ) is to be measured. The length of the cylinders in Fig is L. L is large such that end effects are negligible (we can treat this as a two-dimensional problem). Torque (T) is required to rotate the inner cylinder at constant speed. Showing all your work and algebra, generate an approximate expression of T as a function of the other variables.
The system in Fig. is used to calculate the pressure p 1in the tank by measuring the 15-cm height of the liquid in the1-mm-diameter tube. The fl uid is at 60 ° C. Calculate thetrue fluid height in the tube and the percentage error due tocapillarity if the fluid is ( a ) water or ( b ) mercury.
A vertical, clean, glass piezometer tube has an insidediameter of 1 mm. When pressure is applied, water at20 ° C rises into the tube to a height of 25 cm. After correctingfor surface tension, estimate the applied pressurein Pa.
A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution:
To determine the shear stress of oil, two horizontal plates are placed 15 cm apart, the space between them is filled with the oil of viscosity 15 poise. If the upper plate is moving with velocity 2,000 mm/s, find the shear stress (τ).
Calculate maximum pressure developed in the slider shoe bearing if the fluid with viscosity of 30Pa-s is flowing through the bearing. The top surface of the bearing is moving with velocity of 3m/s and the dimension in the direction of velocity is 25mm with attitude of 2.2. The film thickness at the entrance is 40micron
If the viscosity of water at 70 °C is 0.0042 poise and its specific gravity is 0.97, determine its kinetic viscosity in centistokes.
Find the dynamic and kinematic viscosities of water at 327 K.
Find the dynamic and kinematic viscosities of kerosene, SAE 10W-30 motor oil, and water at a temperature of 38°C (100°F). show solution.
An experiment to measure the viscosity of liquid using a funnel with a cylindrical reservoir