Which terminal command can be used to determine the number of physical connections to a certain location? Does it display you the IP Addresses as well?
Q: What is the source port of the DNS response message? Enter the number of the port only.
A: We are going to learn about whats the source port of DNS response message.
Q: Which protocol dynamically reports errors to source hosts by using IP directly to buildpackets?
A: The Internet Control Message Protocol (ICMP)
Q: What information is required to establish whether or not the destination IP address is a member of…
A: Introduction: When the host process is located on the local LAN, it is possible to communicate…
Q: Which switch command will turn off the Dynamic Trunking Protocol (DTP)? a.
A: Option d Switch port nonegotiate
Q: Which command is used to find the host name of a computer when you know its IP address?
A: IP address is an internet protocol that enables data sharing capabilities in a time network.
Q: Which of the following command is used to manipulate network routing table? a. Route Print O b.…
A: a.) Route print command Route command is useful to view and to manipulate the IP network routing…
Q: Which application protocol is used between two mail servers? Group of answer options SMTP POP…
A: A computer network is a collection of computers connected by digital linkages and using a set of…
Q: Which of the below is a feature in the DHCP server that allows the DHCP administrators to reserve…
A: Computer network: A group of computer system or computer nodes that are connected to each other and…
Q: Which command allow you to request an IP address as a DHCP client? (Choose all that apply.) a) dh…
A: Incorrect options: a) dh dh is a Linux command that helps in executing a set of debhelper commands…
Q: When you run a scan on your computer, you see a session with a host at the IP address What protocol…
A: Given IP address is 208.85.40.44:443 Port 80 indicates this is an HTTP session. Port 80/HTTP is…
Q: e a CISCO PT command to implement a standard or extended ACL in a Router interfac
A: Given:- Write a CISCO PT command to implement a standard or extended ACL in a Router interface?…
Q: I ran the ipconfig command on my computer and it reports an IP address 169.254.75.10 on the ethernet…
A:
Q: Which of the following commands will reboot the router? Router# reload Router# reset Router> reload…
A: Solution:-
Q: Which one of the following commands can be used to view only the IPv6 addressing information on the…
A: Answer : ipv6config command is the right answer.
Q: Which header field is used to reassemble fragmented IP packets? O Acknowledgement field Source…
A: which header field is used to reassemble fragmented IP packets Answer: Don't Fragment bit and…
Q: If you were experiencing difficulties in connecting to a remote service, how might you use the ping…
A: Ping command works with the server name or it's ip address.
Q: Which of the following ports would be used during a domain name lookup? a. 22 b. 23 c. 53 d. 110 e.…
A: When we want to program a server application, we need to specify a port on which it will listen. So…
Q: command is used to determine if an IP access list is enabled on a particular interface
A: refer step 2
Q: The below DHCP Server is configured to server the connected Clients accordingly. DHCP Server IP…
A: Solution: IP address conflict :The conflict of IP addresses happens when two or many devices in…
Q: Which of the following statement refers to the main difference between the operation of inbound and…
A: Answer: Inbound ALCs are processed before the packets are routed while outbound ALCa are processed…
Q: Which device ( switch /router ) can read ip address attached to a sent message ?
A: Ans:- Router is a device which is used to read ip address attached to sent message.
Q: Which of the following commands on a router is true about the command "service password- encryption?…
A: Encryption
Q: Which command is used to give a description for an interface in Cisco router?
A: Explanation: Description command is used to give description for an interface in Cisco routers.…
Q: Which command will be useful in knowing all the hops between two hosts on a network?
A: The command will be useful in knowing all the hops between two hosts on a network - A. Ping B .…
Q: Which of the below cmd command will let the network admin locate which router is not reachable? *…
A: The solution to the given problem is below. ***Note: According to Bartleby policy we are not…
Q: A system administrator at a SOHO remote site would like to modify the range of…
A: The DHCP configuration of a SOHO router can be configured with the beginning and ending DHCP address…
Q: An IT administrator wants to assure that a client PC always acquires the same IP address from a DHCP…
A: 1) A DHCP Server is a network server that automatically provides and assigns IP addresses, default…
Q: Which one of the following commands is used to move from interface mode to privileged EXEC mode on a…
A: Task :- Choose the correct option for given question.
Q: Which terminal-based command can used to find out number of physical links to a certain destination?…
A: An IP address is a unique address that identifies a device on the Internet or local area network. IP…
Q: Which command will configure G0/2 to be a routed port and not a switching port?
A: To Configure the G0/2 we use the int G0/2 .
Q: Which command can be used to verify the routes in a router? A. show interfaces b. show run C. show…
A: Explanation:- The show ip route (protocols) is used to verify the routes in a router. Because the…
Q: Which Scopes is used to assign IPv4 address pools for Class A, B, and C networks in a DHCP Server,…
A: Multicast Scope - Used to assign IP address ranges for Class D networks. Multicast scopes do not…
Q: * Which of the following commands will allow you to set your Telnet password on a Clsco router? O…
A: Q 1 line vty 0 4 The command line vty 0 4 places you in a prompt that will allow you to set or…
Q: Which terminal-based command can used to find out the number of physical links to a certain…
A: For windows the command is tracert
Q: Which TCP port numbers are used for both insecure and secure HTTP (web) traffic, by default? (Choose…
A: ______ Like and thank you _______ Option 4 Option 3 443 80
Q: Which of the following is a form of hub that routes packets to the proper port depending on the…
A: Intro It is the process through which systems decide where to send a packet which is known as…
Q: Which one of the following commands can be used to view only the IPV6 addressing information on the…
A: command to view only IPv6 addressing information is in step 2.
Q: Which of the following statements is INCORRECT when assigning an IP network? Group of answer options…
A: Which of the following statements is INCORRECT when assigning an IP network?Group of answer options…
Q: Which file stores the TCP/IP addresses of the DNS servers used to resolve host names ifno DNS…
A: The transmission Control Protocol/ Internet Protocol is the protocol for communication between two…
Q: Which type of IPV6 address is used to send a single IPV6 packet to multiple destinations? a.…
A: Question from basics of IPv6, we have different types of addresses in Ipv6 like Multicast, Unicast…
Q: The ___________ command is used to display the full TCP/IP configuration for all adapters for a…
A: Command for displaying full TCP/IP configuration Ipconfig/all is the command used for renewing a…
Q: Q6) The administrator assigns an IP address to an interface and activate it. Which route should…
A: Answer: b. C 192.168.0.0/24 is directly connected, FastEthernet 0/0
Q: our computer is configured t
A: ) c. Delegate Administrative responsibilities 2)a. Active Directory Searchb. DNS Lookupc. Text file…
Q: The command below illustrates the configuration of static route. Router(config)# ip route…
A: Dear Student, The function of the parameter distance is to set an administrative distance(AD) whose…
Which terminal command can be used to determine the number of physical connections to a certain location? Does it display you the IP Addresses as well?
Step by step
Solved in 2 steps
- Which router command allows you to view the entire contents of all access lists?Which of the following verification is done when the user has gone through all the test connections through the PING command? Choose an answer A Verify the network adapter B Verify the IP configuration C Verify the physical connectivity D Verify network connectivityWhich parameter is required when redistributing a route into EIGRP? Several factors, such as the next hop's IP address and the exit interface, may influence the administrative distance.
- Your computer is configured to obtain an IPv4 address and DNS server address automatically. Which utility will help you to find the IPv4 address of your computer? (Choose all that apply.)Which application is used to setup IPsec between two computers and how is it done?Which parameter is required whenever a route is redistributed into EIGRP? There are several other characteristics that influence administrative distance, such as the exit interface and the IP address of the following hop.