Why in every city there is a height limit when in fact the code allows it??

Q: 13m bar of negligible weight rests on the smooth planes as shown in the figure. Determine the angle…

A: T=300N x=3m To find angle theta for the equilibrium

Q: Compute the net area of each of the given members (Use standard-size bolt holes for all problems

A: Given data in question  Bolt Diameter= 3/4 inch Plate dimensions = 3/4 ×8 To find out  Net area

Q: Calculate the magnetic declination, if the magnetic bearing of a line is N 81°E and true bearing of…

A: Given data- magnetic bearing- MB=N 81o E, true bearing- TB=N 77o E, To Find- The magnetic…

Q: A rectangular footing of breadth size 3 m and length 5 m is designed on CLAY at a depth of 1.5 m…

A: GIVEN, RECTANGULAR FOOTING 3 m x 5 m clay depth = 1.5 m vertical load = 1200 KN ysoil = 19 KN/m3 Cu…

Q: An irrigator desires to lift a stream of 30 lps a vertical height of 12 m. If the loss of head in…

A:

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A:

Q: The L-shaped gate shown in the figure is designed such that when water reaches a certain design…

A: Option (b) is the correct answer.

Q: P₁ kN- P₂ kN. Determine (approximately) the reactions at the base of the columns of the frame shown.…

A: Portal frames are used in many civil engineering structures like bridges, factories, buildings, etc.…

Q: F ● Particle size analyses were carried out on two soils-Soil A and Soil B-and the particle size…

A: Given, Grain size distribution curve for two soils A and B

Q: For the beam with coordinate shown in figure. Develop the flexibility matrix. 2 B

A:

Q: Problem 2. Determine the latitudes and departures of each course and balance these quantities by…

A: To Determine :- The latitudes and departures of each course and Balance these quantities by…

Q: Identify the zero force members in the shown truss. (SHOW ALL FREE BODY DIAGRAMS PLEASE) Determine…

A:

Q: A soil sample weighing 455 grams when brought from the field in a cylinder of 300 cm3 volume,…

A:

Q: Can you explain how did you het Tab = 1160.695N, Tac...., Tad.....? Just go over equations for last…

A:

Q: Consider the given beam below. Determine the following: 1. Vertical reaction at the hinge support…

A: Given data:-

Q: A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60%…

A: To find out the theoretical head and discharge in case of 1500 rpm.

Q: How much water you can use in 90 days in a weekly basis if you have 1 hectars of soil and you have…

A: Given Total amount of water to be used in 90 days = 15600m³ Required Amount of water to be weekly in…

Q: Please box the final answer

A: from the given coordinate system AB and AC lie on xy- plane and AD lies on xyz plane we first find…

Q: A surveying student had recorded the following afterrepeated pacing:First distance = 200 m.No. of…

A:

Q: A three hinged parabolic arch of rise 5m and span 20m carries a point load of 15kN at quarter span…

A:

Q: The hydraulic conductivity of a sand at a void ratio of 0.71 is 0.044 cm/sec. Estimate the hydraulic…

A:

Q: What are the six possible errors while testing for a specific gravity of hydrated cement?

A: Cement:- Cement is a type of binder used in construction that binds materials together by setting,…

Q: Do an analysis of frames in the given structure. Determine first if the frame is statically…

A: degree of static indeterminacy, DS = 3C - R C - number of cuts to make independent tree-like…

Q: Determine the force in all members of the K-truss shown in the figure below. State whether the…

A:

Q: Answer should be 46.3 lps for theoritical discharge and 343 cm/s for theoritical velocity

A: Given: Head of water above center = 600 mm Orifice opening = (150mm*150mm) Required: Theoretical…

Q: Given the following tabulated data for a closed traverse, determine the bearings of CD and EA.

A:

Q: Calculate the additive and multiplying constant, if the focal length of the objective glass is 250…

A: Given data: Focal length, f = 250 mm Stadia intercept, i = 2 mm Distance of the instrument axis from…

Q: 450 lb E -3 ft- B 30° -3 ft Prob. 1 2. The truss is shown in the figure. (a) Determine the reaction…

A: Objective: To determine the (a) support reactions, (b) check for symmetry of the truss and (c)…

Q: What are the uses of computers in design, using illustrations?

A: There are following use of computers in design.

Q: Part B - Calculating the moment about AB using the position vector AC Using the position vector from…

A: Given data:- Member is anchored at A and section AB lies in the x-y plane.  Dimensions, x1=1.5 m,…

Q: Problem 1. Given in the tabulation below are notes for an open traverse. Determine the latitude and…

A: To Determine :- The latitude and departure of each course and tabulate each computed values…

Q: A 4KN/m 6m 3KN 3m 3m B

A:

Q: As per plan, the distance between two telephone poles is 3566.35 meters. If the location of one is…

A:

Q: Calculate the centroidal moment of inertia and radii of gyration about the centroidal X and Y Axes.…

A:

Q: As shown in the figure below, air is contained in a vertical piston-cylinder assembly such that the…

A:

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: 2. A rod 150 cm long and diameter of 2.0cm is subjected to an axial pull of 20kN. Determine the…

A:

Q: Calculate the forces of all members through method of joints.

A:

Q: A block is of width 60 mm and weight W. A for f friction between block and floor is 0.3. Upto lock…

A:

Q: The hydraulic conductivity of a sand at a void ratio of 0.71 is 0.044 cm/sec, Estimate the hydraulic…

A: Given data in question  Hydraulic conductivity at 0.71 void ratio= 0.044 cm/sec Void ratio 0.55 To…

Q: How to get the shear force V= -P and the bending moment M= -Px

A: Solution_1

Q: Problem 2. Determine the latitudes and departures of each course and balance these quantities by…

A:

Q: The wooden pile has a diameter of 95 mm and is subjected to a load of P = 82 kN. Around the…

A:

Q: If load P = 18.9 kips, determine the normal force in bar (1). D (1) P

A:

Q: 2-45 Saturated refrigerant-134a liquid at 10°C is cooled to 0°C at constant pressure. Using…

A:

Q: If the viscosity of water at 68° F is 0.01008 poise, compute its absolute viscosity in pound-seconds…

A: Viscosity is the measure of the resistance of fluid deformation. it is due to internal frictional…

Q: 3

A: To find:- cuttings concentration

Q: The homogeneous cylinder of weight Wrests in a frictionless right-angled corner. Determine the…

A: given data Frictionless surface right angles corner we draw a free body diagram with respect to…

Q: Using the data of table below, make a plot of final angular

A: Given: Set of Initial angular momentum and final angular momentum is given. To find: the error bar…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.