Why is CMRR dimensionless?

Q: 4- Can you trigger the TRAIC in (Q1 or QIv), explain briefly ?

A: Semiconductor are the material made of pure Si or Ge or compound . They have conductivity in between…

Q: data is calculated at the end of the power flow

A: Power Flow or Load Flow Analysis   It is a computational procedure to determine the steady-state…

Q: What is called EMS? And why Energy Management System is important? What are the applications of EMS?…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is linear time invariant system and their properties?

A: A linear time invariant system is defined as the system whose output is not varying with respect to…

Q: What is the effect of increasing k on time constant & error ? why?

A: Lets analyze it considering first order Transfer function…

Q: What are the methods used to reduce systematic errors? Explain them briefly

A: Systematic error - Systematic errors are errors that are not caused by chance but are caused by a…

Q: What does matched load mean?What happens if the load is not matched?

A: In this question, we will define matched load..

Q: Routh-Hurwitz stability criterion

A: RH criteria is uses characteristic equation or we can say denominator of closed loop system transfer…

Q: Discuss the theory of Buck chopper and explain it ?? (700 to 1000 word limit)

A: A CHOPPER is a circuit that converts fixed DC input voltage to a variable DC output voltage…

Q: 8.8 Explain what is meant by micro stepping.

A: Micro stepping is a process to drive or run stepper motor in which it rotates upto only a fraction…

Q: What do you mean by cascaded systems? How do you get the total gain or attenuation for such?

A: Cascaded system: When two or more system are connected one after another such that the output of…

Q: What is Repeated Measures?

A: There are many measurements of every subject in repeated designs and all subjects are distributed to…

Q: Write a function, comprised of at least 6 step and/or ramp functions with changes occurring only…

A: According to the question, We need to write the expression of a signal xt, which contains 4 step…

Q: Match the steady-state errors (sse) with their values: for each one choose a, b, c, or d R(s) E(s)…

A: Given system without controller is - Given system with controller is -

Q: With necessary sketch, Explain the mode of operation of chopper which is turn off due to external…

A: A chopper is a power electronic device which is basically a dc to dc converter. It is a device which…

Q: A controller is to be designed for the plant for a transportation delay of 0.05 s. Explain briefly…

A: Transportation delay in a control system is the time difference between the Applied input to the…

Q: What is fusing factor ?

A:

Q: Simplify F(A, B₁C₁D₁E) = {m (0.4, 7, 8, 9, 12, 16, 18, 20, 22, 23, 24, 25, 26, 27, 28, 30) woing а)…

A: Given data: FA,B,C,D,E=∑M0,4,7,8,9,12,16,18,20,22,23,24,25,26,27,28,30 Find (a) K-map.

Q: Explain by writing the rules and formulas for drawing a Nyquist curve.

A:

Q: Explain the computational procedure of load flow by "fast decoupled load flow" method

A: Fast decoupled load flow method - ALGORITHM- Step 1: Assume a suitable solution for all buses…

Q: Explain the concept of absolute stability in non-linear system. Also state and explain the Popov…

A: Stability means that the system outputs and its internal signals are bounded within admissible…

Q: What is load regulation?

A:

Q: Their cheap cost is the most significant benefit of single-bus systems.

A:

Q: Each item below describes key characteristics of a particular system (that is, a plant transfer…

A: Hi! Thank you for the question. I am solving the Question for 3 sub-parts Part (a) to Part (c) as…

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring System)

A:

Q: Q1.Explain temperature compensation of strain gauge in detail?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: What is The amount of compensation to keep VR constant in power transmission line performance study?

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Explain the meaning and give a practical significance of the unit step signal and ramp signal

A: Unit step signal  The unit signal is given by the mathematical expression as shown below:  f(t)=0 if…

Q: What is the difference (comparison) between the capability of variation of parameters method and the…

A:

Q: What are noise margins? Why are they important?

A: Noise can be added to a logic signal its transmission through out logic circuit. Because of noise,…

Q: What is the capacity factor?

A: Given data: Adam's Bay wind site Wind turbine G80-2000 Pout= 2000kw k=2.05 c=8.35 m/s h=10 m Site…

Q: What is counter? What is its purpose? asynchronous counter that counts from 0 to 32 ?

A: 4) Counter is a sequential digital circuit which has Number of flipflops connected in cascade. It…

Q: What is meant by impedance matching? Why is impedance matching needed?

A:

Q: Which stability is called as load stability? Why it is called like that?

A: Under the normal conditions, after the system is subjected to a disturbance the ability of a power…

Q: Signals and Systems. Show an example of shifting property with the help of proper CT signal…

A: According to the given question, it is required to determine the shifting property with the help of…

Q: Discuss the effect of adding a zero on time response, through the speed response , overshoot…

A: Zeros are the roots of N(s) (the numerator of the transfer function) obtained by setting N(s) = 0…

Q: What is program block. Your answer What is inertial delay

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: USE A Electrical block diagram to explain a typical n-joint robot driven by Dc electrical motors.…

A: The block diagram of a typical n-joint robot driven by DC electrical motors is shown in below steps.…

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system).

A: RTD's working principle is that the electric resistance of a metal  changes due to change in…

Q: briefly describe the steps involved in the newton raphson method

A: Newton raphson method

Q: Q.Explain sources of noise and its type(electrical amd static noise) in detail?Explain magnetic…

A:

Q: Draw the graphs of the Manchester, differential Manchester, NRZ-I and NRZ-L schemes for each of the…

A:

Q: Describe noise and the effects of noise on communication systems with examples.

A:

Q: inversion

A: Digital signal processing (DSP) refers to the use of digital processing, like by computers or a more…

Q: How do you do Routh Houritz criteria? What is a method that always works? Like how apply to below?

A:

Q: Explain the term concurrent engineering. Why is itimportant?

A: Concurrent engineering means that the manufacturing process and the products are designed…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.