Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat terrain in Bacoor City, Cavite. If the building is classified as Category 5 and under Exposure C with a wind speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of the building. 02. 10 m 30 m 15 m wind D.

Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat terrain in Bacoor City, Cavite. If the building is classified as Category 5 and under Exposure C with a wind speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of the building. 02. 10 m 30 m 15 m wind D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 17P

See similar textbooks

Similar questions

Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat terrain in Bacoor City, If the building is classified as Category 5 and under Exposure C with a wind speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of the building.
Derive the Wind Pressures and Wind Load Parameters for MWFRS - OPEN Building Gable Roof. Code: NSCP 2015 Wind Load Parameters 1. Building Classification/Category: Section 103 Table 103-1 2. Basic Wind Speed: Figure 207A.5-1A,B,C 3. Exposure Category: Section 207A.7 4. Topographic Factor, Kzt: Section 207A.8 5. Wind Directionality Factor, Kd: Section 207A.6 6. Gust Effect Factor, G: Section 207A.9 7. Enclosure Classification: Section 207A.10 8. Internal Pressure Coefficient, GCpi: Section 207A.11 9. Velocity Pressure, qz or qh: Section 207B.3.2 10. External Pressure Coefficient, Cp or CN: Figure 207B.4-5, 207B.4-7, & 207B.4-8 11. Design Pressure, p: Equation 207B.4-3 NOTE: Assume Clear Wind Flow
(a) Determine the wind pressure distributionon the four sides of the 10-story hospital shown inFigure P2.15. The building is located near the Georgiacoast where the wind velocity contour map in the ASCEStandard specifies a design wind speed of 140 mph. Thebuilding, located on level flat ground, is classified as stiffbecause its natural period is less than 1 s. On the windward side, evaluate the magnitude of the wind pressure every 35 ft in the vertical direction. (b) Assuming the wind pressure on the windward side varies linearly between the 35-ft intervals, determine the total wind force on the building in the direction of the wind. Include the negative pressure on the leeward side.
For MWFRS - OPEN Building Gable Roof, find the Wind Pressures and Wind Load Parameters for the roof. Code: NSCP 2015 Wind Load Parameters 1. Building Classification/Category: Section 103 Table 103-1 2. Basic Wind Speed: Figure 207A.5-1A,B,C 3. Exposure Category: Section 207A.7 4. Topographic Factor, Kzt: Section 207A.8 5. Wind Directionality Factor, Kd: Section 207A.6 6. Gust Effect Factor, G: Section 207A.9 7. Enclosure Classification: Section 207A.10 8. Internal Pressure Coefficient, GCpi: Section 207A.11 9. Velocity Pressure, qz or qh: Section 207B.3.2 10. External Pressure Coefficient, Cp or CN: Figure 207B.4-5, 207B.4-7, & 207B.4-8 11. Design Pressure, p: Equation 207B.4-3 NOTE: Assume Clear Wind Flow
Wind blows on the side of the enclosed agriculture steel building located on open flat terrain. If the hasic wind speed is 250 kph and the design is for Main-Wind Force Resisting system (MWFRS), determine the design wind pressure acting on the roof and sides of the building. Use NSCP 2015. Given: Enclosed agriculture steel building Basic wind speed = 250 kph (Category V) Located on open flat terrain (Exposure Category C) The design is for MWFRS Required: Design wind pressure acting on the roof and sides of the building
Determine the external wind pressure on the roof of the rigid-gabled frame of a building for an essential disaster operation center shown in Fig. P2.14. The building is located in Kansas City, Missouri, where the terrain is representative of exposure C and the basic wind speed for risk category IV buildings is 120 mph. Assume the wind direction is normal to the ridge, as shown in the figure. Use Kd 50.85 for main wind-force resisting systems, and Ke =1
A triangular gate having horizontal base of 1.30m and an altitude of 2m is inclined 45° from the vertical with the vertex pointing upward. The base of the gate is 2.60m below the surface of oil (specific gravity= 0.80). What normal force must be applied at the vertex of the gate to open it?
Determine the design wind pressure using the simplified wind method for a building located in South Carolina with a basic wind speed of 110 mph, a height of 25 ft, a wind exposure of C. and an occupancy category of III.
Determine the external wind pressure on the roof of the rigid-gabled frame of a building for an essential disaster operation center shown in Fig. P2.14. The building is located in Kansas City, Missouri, where the terrain is representative of exposure C, and the basic wind speed for risk category IV buildings is 120 mph. Assume the wind direction is normal to the ridge, as shown in the figure.
Wind can produce very high drag loads on high-rise bulidings. Since calculating the áow around a buildingis quite diffcult, you decide to perform an experiment to find the drag on the nearly completed Mirabellabuilding at Univesity Drive and Myrtle Avenue in Tempe. The building is 250 ft tall and approximately 210ft wide (at its widest part) A) determine the drag on the Mirabella building for a sustained wind speed of 40 mph. Supposethat the temperature remains the same both inside and outside of the wind tunnel test section. If theatmospheric pressure is 100 kPa, what would the pressure have to be inside the tunnel test section tomaintain dynamic similarity between the model and the full-scale building? (You may assume that thetunnel is operating at maximum speed.
Given: ▪ Proposed Eight-storey with roof deck commercial mix use building▪ 20 x 32 m with first floor being 3.5 meter in height and rest at 3.2 meter with 1.0-meter parapet ▪ 5 bays x 7 bays (5@ 4-meter x 8@ 4 meter typical) ▪ Assume a 10 kPa regular weight of the typical floor area except at roof deck being 8 kPa. Occupancy Category IIIEnclosedWind speed, V= 260kphExposure C Calculate the required wind pressure on the walls and parapet applying the code provision under Directional Procedure for Buildings of All Heights (NSCP section 207B) **ALL UNITS MUST BE IN KILOPASCAL (kpa)photos for reference
A two-storey light storage warehouse has interior columns that are spaced 12 ft apart in two perpendicular directions. If the live loading on the roof is estimated to be 25 ??/??^2, determine the reduced live load supported by a typical interior column at (a) the ground-floor level, and (b) the second-floor level.