with a diameter of 50mm and a length of 225mm. The right segment is bar YZ whose diameter is 75mm and a length of 300mm. The Modulus of Elasticity of the bar is 6 GPa and the Linear Coefficient of Expansion is 100 X10-6/0C. Determine the following if the temperature changed by 30°C: a. The thermal deformation of the bars b. The compressive force acting in the bars c. The maximum compressive stress d. The displacement of pont Y

with a diameter of 50mm and a length of 225mm. The right segment is bar YZ whose diameter is 75mm and a length of 300mm. The Modulus of Elasticity of the bar is 6 GPa and the Linear Coefficient of Expansion is 100 X10-6/0C. Determine the following if the temperature changed by 30°C: a. The thermal deformation of the bars b. The compressive force acting in the bars c. The maximum compressive stress d. The displacement of pont Y

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.12P

See similar textbooks

Similar questions

A 200 mm long, stress free rod at room temperature is held between two immovable rigid walls. The temperature of the rod is uniformly raised by 250°C. If the Young's modulus and coefficient of thermal expansion are 200 GPa and 1×10^-5/°C respectively, the magnitude of the longitudinal stress (in MPa) developed in the rod is _______ A. 600 MPa B. 200 MPa C. 500 MPa D. 250 MPa
stress and strain A steel rod is 0.02 mi n diameter, and 2.5 m in length. The modulus of elasticity of this material is 210 GPa and a Poison's Ratio of 0.2. The change in diameter after applying a tensile force of 150 KN is
A steel rod of circular section tapes from 2 cm diameter to 1 cm diameter over a length of 50 cm. If the modulus of elasticity of the material is 2*10^ 6 kg/cm^ 2 , then the increase in length under a pull of 3000 kg will be
A 20 m steel rod is heated from 260C to 460C. Find the total elongationof the rod if coefficient of the thermal expansion of steel is 11.5 x 10-6m/m-0C.A. 4.60 mm C. 6.78 mmB. 2.34 mm D. 7.34 mm
An elastic rod with a cross-sectional area A = 2mm2 is stretched from an intial legth of 1.0m to a final legth of 1.1m at a constant tempreture of 15 degrees celcius . Calculate the heat exchanged between the elastic rod and its surroundings if it is made of a material with a isothermal Youngs modulus ET = 150GPa and a linear expansivity at constant tension af = 15 x 10 -6 K-1. a) 129.6675 J b) -129.6675 J c) -6.75 J d) 6.75 J
A railway line is laid so that there is no stress in the rails at 8°C. The rails are 30 m long. Take temperature coefficient as 12 × 10^-6 /°C and modulus of elasticity of rail material as 2 × 10^5 MPa. The expansion allowance is 12 mm per rail. The maximum temperature rise to have no stress in the rails is
A cylindrical component 0.3 m long is solid for 1/3 of its length and hollow with inner diameter ½ the outer diameter for the rest of the length. At 300C a gap of 0.1 mm exists between the component and the rigid supports. The outer diameter is 60 mm and the stress is not to exceed 150 MN/m2. Determine the maximum temperature that will not cause failure of the component. Take α as 1.3x10-5/0c and E as 200 GN/m2
A composite bar is made up by connecting a steel member and a copper member rigidly fixed at their ends.The cross-sectional area of steel member is A cm^2 while that of the copper member is 2A cm^2 for half the length and A cm^2 for the other half of the length. the coefficient of expansion of steel and copper are α and1.25α respectively while the elastic moduli are e and 0.5E respectively. Estimate the stress induced inmembers due to temperature rise of T degrees.
Temperature stresses A composite bar is comprised of a concentric circular rod of copper and a tube of aluminium, each of length 500 mm, that are attached rigidly to above one another at both ends. The diameter of the copper rod is 30 mm, while the inner and outer diameters of the aluminium rod are 50 and 60 mm, respectively. The Young’s modulus and coefficients of thermal expansion for copper and aluminium are given as, 120 GPa and 80 GPa, and17 × 10−6 oC and 23 × 10−6/ o?, respectively Please show all formulas and substitutions into formulas 1 Calculate the magnitude of the stresses that are induced in the copper bar and aluminium rod if the composite bar is exposed to a temperature change of 500 oC, and state their senses. 2 Calculate the elongations of the constituents of the composite bar.
A steel pipe with a 50 mm outside diameter and a 43.75 mm inside diameter surrounds a solid brass rod 37.5 mm in diameter as shown. Both materials are joined to a rigid cover plate at each end. The assembly is free to expand longitudinally. The assembly is stress free at a temperature of 27 degree C. For steel, Young's modulus is 200 GN/m^2, and the coefficient of linear thermal expansion is 11.7 x 10^-6 1/degree C. For brass, Young's modulus is 93.33 GN/m^2, and the coefficient of linear thermal expansion is 1.872 x 10^-5 1/degree C. What is the stress in the steel tube when the temperature is raised to 121 degree C?
One spring is placed inside the other, not touching each other, and compressed between a pair of parallel plates until the distance between the plates is 40 mm. Make a neat detailed sketch of the spring and plate assembly. If G = 83 GPa for both springs, calculate the following: 1. The force applied to the spring assembly. 2. The shear stress induced in each spring. 3. The total strain energy stored in the spring assembly. 4. The stiffness of each spring. 5. The equivalent stiffness of a single spring that can be substituted in place of these springs.
Q2) ACED frame is pinned at C and support by two identical wires at A and B. The two wires have modulus of elasticity E = 70 GPa, cross sectional area A = 250m * m ^ 2 and thermal expansion coefficient alpha=23*10^ -6 1/C . a) IfP P = 1000N , Determine the force in each wire. b) If in addition to the load P, the temperature of two wires raised by 120 Determine the force in each wire. c) To what value the temperature will increased in order to make the slack? C. wire at B