10:27 AMworksheet of module 9 R...Worksheet # 1 (module 10 Ratio and Proportion MMW)A. Find the value of the unknown:1. 12:15 = n : 122. 12:18 = 54 : n3. 11: n = 330 = 4504. n: 15 = 54 : 815. 5:12 = 35: n6. 6.4: n = 20 : 8.57. n: 1.5 = 8:38. 8.2: 41=n: 59. 12:18 = n : 9910. 27: n = 9:1576%-

according to bartleby policy we supposed to do only first part of multiple question (1) given…

Answered: Worksheet # 1 (module 10 Ratio and…

Elementary Geometry For College Students, 7e

7th Edition

ISBN:9781337614085

Author:Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:Alexander, Daniel C.; Koeberlein, Geralyn M.

Chapter9: Surfaces And Solids

Section9.2: Pyramids, Area, And Volume

Problem 43E

See similar textbooks

Similar questions

A stamped sheet steel plate is shown in Figure 164. Compute dimensions AF to 3 decimal places. All dimensions are in inches. A=_B=_C=_D=_E=_F=_
Four sets of equally spaced holes are shown in the machined plate in Figure 13-4. Determine dimensions A, B, C, and D to 2 decimal places. All dimensions are in millimeters. A=_B=_C=_D=_
In Exercises 17 and 18, refer to the following sentence and to the following given vernier caliper settings to find values A, B, and C. "The zero vernier scale graduation lies between A and B on the main scale, and the vernier graduation Ccoincides with the main scale graduation." The answer to the first part of Exercise 17 is given.
The tables for Exercises 15 and 16 give the position of the zero graduation on the vernier scale in reference to the main scale and the vernier scale graduation that coincides with a main scale graduation. Determine the vernier caliper settings. The answer to the first part of Exercise 15 is given
This casting in Figure 5-4 shows seven tapped holes, A-G. The number of threads is determined by dividing the depth of the thread by the thread pitch. Find the number of threads in each of the tapped holes. All dimensions are in inches. A=_B=_C=_D=_E=_F=_G=_
Tsunami Waves and BreakwatersThis is a continuation of Exercise 16. Breakwaters affect wave height by reducing energy. See Figure 5.30. If a tsunami wave of height H in a channel of width W encounters a breakwater that narrows the channel to a width w, then the height h of the wave beyond the breakwater is given by h=HR0.5, where R is the width ratio R=w/W. a. Suppose a wave of height 8 feet in a channel of width 5000feet encounters a breakwater that narrows the channel to 3000feet. What is the height of the wave beyond the breakwater? b. If a channel width is cut in half by a breakwater, what is the effect on wave height? 16. Height of Tsunami WavesWhen waves generated by tsunamis approach shore, the height of the waves generally increases. Understanding the factors that contribute to this increase can aid in controlling potential damage to areas at risk. Greens law tells how water depth affects the height of a tsunami wave. If a tsunami wave has height H at an ocean depth D, and the wave travels to a location with water depth d, then the new height h of the wave is given by h=HR0.25, where R is the water depth ratio given by R=D/d. a. Calculate the height of a tsunami wave in water 25feet deep if its height is 3feet at its point of origin in water 15,000feet deep. b. If water depth decreases by half, the depth ratio R is doubled. How is the height of the tsunami wave affected?
Three holes are bored in a checking gage. The lower left edge of the gage is the reference point for the hole locations. Sketch the hole locations and determine the missing distances. From the reference point: Hole #1 is 1332 to the right, and 158up. Hole #2 is 2164 to the right, and 2316up. Hole #3 is 314to the right, and 312up. Determine: a. The horizontal distance between hole #1 and hole #2. b. The horizontal distance between hole #2 and hole #3. c. The horizontal distance between hole #1 and hole #3. d. The vertical distance between hole #1 and hole #2. e. The vertical distance between hole #2 and hole #3. f. The vertical distance between hole #1 and hole #3.
What is the complete proportion for Question 8? The question is about the figure to the right, and the incomplete proportion is MN/RQ = LM/?
2 The window shown in the figure below is made from a given frame'length(L). Find the ratio (h/r) that maximize the area of tiis window.
If two similar solids have a scale factor of a:b, then corresponding areas have a ratio of a2:b2, and corresponding volumes have a ratio of a3:b3.
A machinist is required to manufacture a circular metaldisk with area 100 cm2 . (a) What radius produces such a disk?(b) If the machinist is allowed an error tolerance of + - 5 cm2in the area of the disk, how close to the ideal radius in part (a) must the machinist control the radius?
The area of a triangle with sides of lengths a and b and contained angle θ isA =12 absinθ(a) If a = 2 cm, b = 3 cm, and θ increases at a rate of 0.2 rad/min, how fast is thearea increasing when θ = π/3?(b) If a = 2 cm, b increases at a rate of 1.5 cm/min, and θ increases at a rate of 0.2rad/min, how fast is the area increasing when b = 3 cm and θ = π/3?(c) If a increases at a rate of 2.5 cm/min, b increases at a rate of 1.5 cm/min, andθ increases at a rate of 0.2 rad/min, how fast is the area increasing when a = 2cm, b = 3 cm, and θ = π/3?

SEE MORE QUESTIONS

Recommended textbooks for you

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Functions and Change: A Modeling Approach to Coll…

Algebra

ISBN:

9781337111348

Author:

Bruce Crauder, Benny Evans, Alan Noell

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Worksheet # 1 (module 10 Ratio and Proportion MMW) A. Find the value of the unknown: 1. 12:15 =n : 12 6. 6.4: n = 20 : 8.5