Write a CNC Milling program to machine the outer profile of a 6 mm thick aluminum sheet. Cutting parameters: depth of cut 3 mm, speed 1200 rpm, feed rate 100 mm/min, and coolant. Tool size 8 mm. (you can use the tool cutter compensations codes). Use an absolute coordinate from the point identified as tool position. 10 10 R 10 R 10 Tool position z, 10 mm above the sheet 20 All units in mm 20

Write a CNC Milling program to machine the outer profile of a 6 mm thick aluminum sheet. Cutting parameters: depth of cut 3 mm, speed 1200 rpm, feed rate 100 mm/min, and coolant. Tool size 8 mm. (you can use the tool cutter compensations codes). Use an absolute coordinate from the point identified as tool position. 10 10 R 10 R 10 Tool position z, 10 mm above the sheet 20 All units in mm 20

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.5: Introduction To Cnc Milling

Problem 7RQ: A programmable indexing fixture creates a fourth axis called a ________ __________ that is similar...

See similar textbooks

Similar questions

Describe G03 used in a CNC milling machine G-code. The description has toinclude the syntax of both versions and a detailed example should be provided. Please help, thanks.
Q: Describe G03 used in a CNC milling machine G-code. Include the syntax of both versions and give a detailed example.
Briefly describe the use of I and J for the arc center method of circular interpolation.
Hi, How would you solve this manually without an equation solver
4. Write an APT NC Part program (milling and drilling) for the following work part.The outline of the part shown in Figure is to be profile milled using a 30 mm diameter end mill cutter. The part is 15 mm thick. Use the lower left corner of the part as the origin in the x-y axis system. The two holes are already drilled to fix the work part in the machine (no need to include in program). Use absolute positioning. The program style should be similar to the explanation in PPT. The expected answers – 1. To define all the positions of holes, curves and lines. 2.Movement of cutter outside the work part. 3.Step by step movements for drilling.
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance between the fixed center is (225+X)mm. The length of the slotted lever is (525+X)mm. Determine the ration of time of cutting stroke to time of return stroke. Also calculate the length of the stroke . Note where X is two digit number made from the last two digit of the registration number of the students For example if the reg. no. of the student is 11912081 then X=81 and crank length is 80+81=161mm Draw the neat and clean diagram with proper scale. Rough drawings will not be considered
Please solve step by step as following the problem instructions
Pls see image for instructioms
#5. On the part below, calculate the allowable min and max hole sizes as well as the size of the MMB position boundary created. Please refer to attached image.
Pls see instructions in the attached image.
Provide an FBD in this given problem