Determine the velocity of slider C (link 4) and the velocity of slider B (link 5) assuming link 2 is rotating CW at 500 rotations per hour CCW. Assume all measurements or dimensions provided are in cm. All diagrams are to scale with the indicated lengths/coordinates. Please show your work. Use the velocity polygon method to solve. Thank yo

Determine the velocity of slider C (link 4) and the velocity of slider B (link 5) assuming link 2 is rotating CW at 500 rotations per hour CCW. Assume all measurements or dimensions provided are in cm. All diagrams are to scale with the indicated lengths/coordinates. Please show your work. Use the velocity polygon method to solve. Thank yo

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.20P: Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).

See similar textbooks

Similar questions

In the figure shown, the deflection of mercury is initially 250mm. If the pressure at a is increased by 40kPa, while maintaining the pressure at b constant, what will be the new mercury deflection?
The figure shows the cross section of three cylinders, 1m long, given the density of steel 500 lbs/cu.ft. Find the reactions between all of the cylinders and the ground in lbs. Units are in feet.
Three cylinders A, B, C of diameters, 200mm, 200mm, 100mm and weighing 400N, 400N, 200N, respectively, are placed in a trench as shown in Fig(5). Find the reactions at all contact points.
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
4. A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25° angle with the crane (see figure below). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 mfrom the upper end of the crane. When the crane is raised to 55° above the horizontal holding an 11,000N pallet of bricks by a 2.2 m, very light cord, find (a) the tension in the cable and (b) the horizontal andvertical components of the force that the axle exerts on the crane.
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.
2. ANSWER A AND B WITH DETAILED SOLUTIONS AND COMPLETE FREE BODY DIAGRAM
Anchor point of the beam given in the figure is fixed support and B point is movable support. Find the support reactions.
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
the facade of a house consists of two cylindrical pillars placed at 1 m at the ends of a beam, these pillars support a steel beam of 320 kg and 6 m in length. the center of mass of the beam is at 2.8 m starting from the left end. at each end a new circular column was placed in order to raise a second floor, each of these columns has a mass of 120 kg. if it is considered that the structure must support 2100 kg distributed every 1.5 m, what will be the reaction of each column in the lower zone?
(a) In Fig. a6.00-m-long, uniform beam is hangingfrom a point 1.00 m to the rightof its center. The beam weighs 140 Nand makes an angle of 30.0° with thevertical. At the right-hand end of thebeam a 100.0 N weight is hung; anunknown weight w hangs at the leftend. If the system is in equilibrium,what is w? You can ignore the thicknessof the beam. (b) If the beammakes, instead, an angle of 45.0° withthe vertical, what is w?
a) The second moment of area about the centroidal x-axis (IXXcentroid) for the solid homogeneous beam section shown below is 737,101.55 mm4. What is the second moment of area about the centroidal y-axis (IYYcentroid). Give your answer in mm4 to two significant figures. b) If the second moment of area (IXX) for the solid homogeneous beam section shown below is 917,387.73 mm4, determine the diameter d. Give your answer in millimetres (mm) to two decimal places.