Write an equation for P1 including all the variables shown below.

Q: A spherical balloon is inflated so that its volume is increasing at the ft3 rate of 9 min the radius…

A: Write the expression for the volume of the spherical balloon.

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: .. How long it will take to reach 100 °C.

A: 18.67 seconds

Q: s 5 then find the value of X

A: Need to find value of X

Q: he answer in M1 is 4283.29lb, can you show me how to get this answer

A:

Q: ine the centI ers.

A: given:

Q: per of degrees of free nanism shown below is

A: introduction:here we have to find out dof

Q: Find out total elapsed time

A:

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: The formula defines: Select one: 1. Absolute Error

A: The given formula is

Q: I needed it to be solved using differential equation

A:

Q: In the figure below, Which of the following represent the dedendum

A:

Q: t² + 5t°) m, where t is in seconds. Determine the from t = 1s to t = 3 s. Also, find the average spe

A:

Q: Write down berniullis equation

A: It is required to write Bernoulli equation

Q: Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps

A: Draw the free-body diagram of section DC. Apply moment equilibrium about point D.…

Q: Determine eq.uations and frequuency for the following figure

A:

Q: ADISIDO diameter is 10 times the tube thickness, find the thickness (mm) of the tube.

A: Given   Load, P = 500 kN     Stress = 140 MPa Find   Thickness, t

Q: Give at least 3 examples of measures of position

A: The 3 examples of measures of position are listed below: 1. Percentile: The percentile is a score or…

Q: Compute the piston displacement in cubic meter for every quarter of an hour of a single-stage,…

A: The piston displacement is 31.14 m3.

Q: Sketch a meat tenderizer mallet. And can you show me the measurement of it.

A:

Q: two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the…

A: Fill rate is the percentage of total volume which is filled by plastic. For given problem, fill rate…

Q: 2. Show the HGL and EGL for the conceptual system shown below for the following conditions: SHOW…

A: (a) Consider the diagram shown below for the EGL and HGL neglecting the minor losses.

Q: Calculate Degree of freedom for the following figures.

A: (i) Degree of freedom is calculated by using the formula DOF=3l-1-2j-h

Q: Find the degrees of freedom using grueblers equation

A:

Q: A tire gauge registers 32 lbs/in^2 when air in a certain tire is at 10°C. After running for a time,…

A:

Q: A transmission shaft used to transmit power of 55 kW. During transmission shaft is subjected to a 30…

A: Given data: The power transmitted by the shaft is P = 55 kW. The torque acting on the shaft is T =…

Q: outside what is the temperature in C? What is the temperature for K? The oven is 498K What is the…

A:

Q: Q1-In the figure given below calculate the of (H) for the given data:

A:

Q: Solve for the mobility. Show your logical and accurate solutions after every figure.

A: Solution:   Note: The number of links are designated as numbers while the number of lower pair…

Q: In Problems 1-18 use Definition 7.1.1 to find L{f(t)}. f(t) = e' cos t

A:

Q: Create the model shown in Figure 8-118. The views and dimensions of the model are given in the same…

A:

Q: Can you please explain why in step 2 the written formula are not matching

A: Hello student  In step 2 for optimal compressor ratio in each stage, the following formula is used

Q: Calculate the value of R shown in Figure 1

A: Need to find the value of R.

Q: Compute the position and arientation o

A:

Q: Determine the value of the coefficient of res

A:

Q: If the number of cycles are less than 106, then the corresponding endurance is known as

A: if the number of cycles are less than 10^6,then the corresponding endurance is known as intermediate…

Q: Derive the formula of

A: Solution given below.

Q: Q1:Find an equation for the tangent to the curve at the given point.

A:

Q: Choose the following and define also

A: Given; Wet steam flows through a throttle valve and remains wet at exit,Throttle valve is used for…

Q: MPa. What is the maximum pipe diameter that the wire can be stretched around without yielding and…

A: Given: Li=345 mmdi=1.5 mmE=190 GPa=190×103 MPaσ=275 MPa To determine: The diameter up-to which the…

Q: Write the formula for Macaulay Functions?

A: Formula for Maculay function can be given as ±E×I×d2YdX2=MWhere E is elastic modulusI is moment of…

Q: Find the motor size (KW) needed to provide the forced-draft service to a boiler that burns coal at a…

A: The motor size is 4.7002 kW.

Q: Sketch a typical turbine speed (rpm) VS wind speed characteristics (which indicates how turbine…

A: Given :- Rated speed = 18 rpm