per of degrees of free nanism shown below is

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Figure (3)

A:

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: -bide and ste exponent of 0.

A:

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Given data : Inside diameter=ID Outside diameter=OD   To find : Thickness of steel

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: J,ピと

A: Step 1: To obtain the natural frequency of the above given system, try to write down the motion…

Q: In a single diameter s and thickn of thickne

A:

Q: show the step by step by constructing this using Solidworks. pls

A: Given 3D model To find Steps for modeling

Q: with respect to = 30° with the ientation of the a.

A:

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: of degrees of freedom

A: To find DOF (F)

Q: CONES AND CYLINDERS.

A: kindly refer attachment.

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: che magnitude

A:

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: In the figure below, Which of the following represent the dedendum

A:

Q: Write down berniullis equation

A: It is required to write Bernoulli equation

Q: Calculate the following:

A: Given that ,  Specific gravity = 0.825 at 60°F Mean average boiling temperature = 288°F

Q: N =24 5- To calculate number of grains used

A:

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: N*=24 5- To calculate number of grains used

A: Given: Grains are small size crystal that combines and formed a solid material.

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Outside diameter, do=5 inInside diameter, di=4 in

Q: What is the least moment of inertia?

A: The moment of inertia is given by the following expression: I=MK2 Here, M is mass of the object K is…

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: A/ Draw (F.B.D) for the rod (200N) shown in Fig. (1-a).

A: F.B.D. consist all external force and reaction apllied on Rigid body. For solution refer below…

Q: Lacate the centacid of the blane sheded ora shown below

A: Given Data The radius of the quadrant is: r=16 cm The side of the internal square is: a=8 cm To…

Q: Calculate Degree of freedom for the following figures.

A: (i) Degree of freedom is calculated by using the formula DOF=3l-1-2j-h

Q: Is this for number 1 only?

A:

Q: y. what is the change in length in mm? k for =

A: Need to find change in length.

Q: ely. What would be the reading on new scale corresponding to 50°C?

A: Determine the New scale reading corresponding to 50 deg c.

Q: provide a detail working of how to find inertia (I)

A: we have to evaluate the moment of inertia of I section

Q: 2 Find T: For q=-KA when dr

A:

Q: Find the degrees of freedom using grueblers equation

A:

Q: what is the angle in red?

A: Given Figure to find the angle marked in red color

Q: Determine an appropriatenes OR Poor) of the given dimens (from 1 to 15) shown in Figure If your…

A: Given Data⇒

Q: diameter of the riser (in cm)

A: Given,  Dimension of a cylindrical side riser is= 25 cm×15cm×5cm Tabulated data is given as,  Shape…

Q: Define Mohr’s circle?

A: Mohr's circle is a graphical illustration that allows visualizing the variation of normal stress and…

Q: Apply Bernoulli Equation to figures (1) and (2).

A:

Q: hanism shown in the figure is

A:

Q: shown below. A e large diamete

A:

Q: e of 5 mm. TI d opposite to

A:

Q: How many Iron atoms are there in 2000 pounds of Iron?

A: Given data: Mass of the iron (m) = 2000 pound                                  = 907.2 kg…

Q: What is the Vertical Reaction at B in kips

A: The provided beam is an indeterminate beam since the number of reactions are more than the number of…

Q: The best approximation for a,

A: Given data, Flywheel having mass=m Rim of radius=RConcentric disk like feature of radius=R/2Flywheel…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.