Write an expression for how far the spring is stretch when the cart is at rest in the equilibrium position. Name thisdistance y-naught. Thanks!

Q: Determine the maximum incline e [degrees] that the car can drive up if it has front-wheel drive.…

A: Disclaimer:“Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The force applied on the spanner handle while closing a nut generates a ___________   Select…

A: The force applied on the spanner handle while closing a nut generates a ___________ Answer: Moment

Q: 350kN F N

A: When two surfaces are sliding or trying to slide over another, friction forces act between them.…

Q: The articulation of the braking system consists of the DAB pedal arm, the connecting rod BC and the…

A:

Q: a. How fast is the ball moving as it leaves the spring? (Point B on the diagram. Point B is the…

A: As No friction in the system, Apply energy(here kinetic energy + Potential energy) conservation…

Q: FIND THE FORCE REOUIRED To STOP AN OBUECT FROM S6I DINE 25 ° NCLINED PL VE. THE 65 kg. ON A MASS OF…

A: Hi and thanks for the question. Since you have asked multiple questions, we will solve the first…

Q: calculate the value of the static friction force acting on the disk D at the instant it starts its…

A:

Q: If a load of 100 N at 45° is to be balanced by another mass kept at twice the radius of rotation as…

A: Given data:

Q: Use the curve to determine the current the motor/gearmotor will draw while lifting the 0.5 kg mass.

A: Force acting on the shaft F = 0.5 kg considering perpendicular distance r = 1 cm   Torque acting on…

Q: This frame is sym metric but not a symmetrically Toaded, solve rertical tha+ SAlve rertical that In…

A:

Q: metermine the maximum weight of the engine that can be supported without exceeding a tension of 430…

A: Given Tension  in the chain AB, TAB=450 lb  Tension in the chain AC , TAC=480 lb Let W= Maximum…

Q: Draw free-body diagrams of members AC and BG 3 m -8 m G 2 m 15 2 m 8 2 m A 300 N 3**3**3*

A:

Q: ension in the vertical cable while the

A: The tension in belt would be  = Mg  =2*9.8 =19.6N

Q: The box of mass m = 10 kg is in motion. What is the minimum force F needed to keep it moving?

A: Given that: m = mass of the body = 10 kg coefficient of static friction = 0.2 coefficient of kinetic…

Q: 4.a Draw the free body diagrams and derive the equation of motion.

A: 1. Two Masses-Two Springs system of vibration 2. All spring constants are equal i.e., k1 = k2 = k3 =…

Q: Using the diagram of problem 1. Determine the tension developed in the ble. The coefficient of…

A: Given: s= 6 m W=20 kg μk=0.3 t=3 s To determine: Tension in wire

Q: Develop the equation of motion in terms of the variable x for the system shown Draw free body…

A:

Q: 1. Attempt Any TWO (I 1. Derive the equation to find the balancing mass and its angular position in…

A: 1 - Suppose there are two static unbalanced masses in a plane  described as -  Masses - m1 and…

Q: At midpoint, the cord is pulled rightward until it makes an angle of 40° with the horizontal…

A:

Q: n forces in the pin A and roller B,

A:

Q: Draw the FBD and derive the EOM of the pulley system below with respect to x using Ne

A:

Q: Calculate the focus reaction at A and B due to the force load of 1000 lb fan coupling 2000 lb. ft…

A:

Q: Determine the constraint equation that relates the bodies A and B.

A:

Q: A bas weighing 100 N is at rest on a horizental floor. The coefficient of the statice frietion…

A:

Q: if two forces of body, then their gnitude P and 2p act minimum resceltant ma on is

A: Given data: F1=PF2=2P Need to determine the minimum resultant force.

Q: (i) Make a rough copy of the figure. Draw arrows on your copy to show the weight of the object and…

A:

Q: Identify the limbs of the given mechanism, determine the degree of freedom and form the kinamatic…

A:

Q: 3/19 Determine the minimum cylinder mass m1 required to cause loss of contact at A.

A:

Q: When the normal force N and friction force F be in the position shown, it means that the body is…

A:

Q: Using the equilibrium concept, calculate the magnitude of F1 and its direction ф as shown in the…

A:

Q: Sketch the free-body diagram of the cylinder.

A:

Q: The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect…

A: Given:WA=300 lbWB=400 lb

Q: A ball governor pe rev/min. The bell-crank lever arms are 150 mm and 75 mm an e a mass of 2.75 kg…

A: Vertical arm kength(a)=150 mm Horizontal arm length, b=75 mmSpeed range of governer at mean speed…

Q: Figure Q1 shows a high-pressure hand pump used for boosting oil pressure in a hydraulic line. The…

A: (A) There is only a single member i.e CE which is a two force member, subjected to axial force and…

Q: h diagrams and figures the independent suspension system used for the cars and also for the heavy

A: INTRODUCTION Independent suspension is any car suspension framework that permits each wheel on a…

Q: A weight of mass m is at rest at O when suspended from a spring, as shown. When it is pulled down…

A: the last option is correct. the elastic potential energy is smallest at o.

Q: A meter stick with a mass of 0.156 kg is pivoted about one end so it can rotate without friction…

A:

Q: 4. The 60 kg crate has its center of gravity at G. Coefficient of static frictión is 0.3. a) Find…

A:

Q: A -P C

A:

Q: system sh as a mass of 100 kg concentrated at G and carries a lo s held in equilibrium with the wall…

A: Both the question are different so ask second part as new question

Q: with twice the force as comparec change in length (m) of spring B?

A: To find change in length

Q: he 100 kg C ring moves on the BD rod without friction. Calculate the force on the AC chain for the…

A: The vector from B to C is nowrBC=8meter  eBD     =849i-79j+49k

Q: Draw free body diagram for the dynamic model of the mechanism write dynamic equilibrium equations…

A:

Q: The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect…

A: Weight of A= 230 lb Weight of B = 300 lb

Q: magnitude of the reaction force on the bearing A?

A: To find Reaction force at bearing A

Q: Torsional springs provide a simple propulsion mechanism for toy cars. When the rear wheels are…

A: Given, Weight of the car  = W = 5 oz Mss of the car = m = 0.009713 slug (From 5 oz)Weight of wheels…

Q: what is the compression in 2 springs after the block A with 50 N is falling off on it from the rest…

A:

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.