Write down the nodal equations of the circuit shown, take node D as the reference node. Applying KCL at node A yields: equation (1) Applying KCL at the supernode BC yields: equation (2) Relating the node voltages of the supernode with the voltage source yields: equation (3) From equations (1), (2), and (3) calculate the node voltages VA, VB, and Vc. Record your results in Table 1.

Write down the nodal equations of the circuit shown, take node D as the reference node. Applying KCL at node A yields: equation (1) Applying KCL at the supernode BC yields: equation (2) Relating the node voltages of the supernode with the voltage source yields: equation (3) From equations (1), (2), and (3) calculate the node voltages VA, VB, and Vc. Record your results in Table 1.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter33: Alternating Current Circuits

Section: Chapter Questions

Problem 33.7P: An audio amplifier, represented by the AC I source and resistor in Figure P33.7, delivers to the...

See similar textbooks

Similar questions

Discuss possible practical applications of RL circuits.
In Figure OQ32.4, the switch is left in position a for a long lime interval and is then quickly thrown to position b. Rank the magnitudes of the voltages across the Four circuit elements a short time thereafter from the largest to the smallest.
Do Kirchhoff’s rules apply to circuits that contain inductors and Capacitors?
In an oscillating RLC circuit, R = 7.0 L. = 10 mH. And C = 3.0 F. Initially, the capacitor has a charge of 8.0 C and the current is zero. Calculate the charge on the capacitor (a) five cycles later and (b) 50 cycles later.
An audio amplifier, represented by the AC I source and resistor in Figure P33.7, delivers to the speaker alternating voltage at audio frequencies. If the source voltage has an amplitude of 15.0 V, R = 8.20 . and the speaker is equivalent to a resistance of 10.4 . what is the time-averaged power transferred to it?
Check Your Understanding Show that the tins voltages across a resistor, a capacitor, and an inductor in an ac circuit where the tins current is Irmsare given by IrmsR,IrmsXC , and IrmsXL, respectively. Determine these values for the components of the RLC circuit of Equation 15.12. Pave=12t0v0cos (15.12)
The two frequencies wi-fi uses a current 2.4 GHz and 5.0 GHz. What are the angular frequency for circuit oscillation?
In circuit C, L=100mH and C=100uF are connected in series. In circuit Y, L=100 and C=1uF are attached in parallel. The resonating frequency f, and f, are related as:
To get the minimum current, the connection should be in series. If you create a series connection with 30V DC source and three resistors with R1 = 50Ω, R2 = 75Ω, and R3 = 100Ω, how do you calculate for the total current (IT) and the current flowing in each resistor (I1, I2, I3), and the total voltage (VT) and the voltage across each resistor (V1, V2, V3)? How do you also determine the power dissipated by each resistor (P1, P2, P3) and by the whole circuit (PT)??
Consider a series RLC circuit for which R = 150 Ω, L = 20.0 mH, ΔVrms = 20.0 V, and ω = 5 000 s-1. Determine the value of the capacitance for which the current is a maximum.
. A capacitor of capacitance 80 µF is giving supply voltage V= 10 Sin ωt to one end of an oscillator. How can you evaluate the peak voltage of the circuit, if ω is changing from 10 to 100 rad/sec? Evaluate the difference between the peak values during the change of ω from 10 to 100 rad/sec. The capacitor acts an open circuit here. Justify your answer?
Consider the RLC circuit shown below, where the initial current flowing through the circuit at time t=0 is I_0 = 5, and the initial charge on the capacitor at time t=0 is Q_0 = 2. The components have values of R = 100 ohms, L = 5H, and C = 1/450,500 F. Write a differential equation for Q(t), the charge across the capacitor, assuming the voltage source V(t)=0.