Answered: Write the 2nd order differential…

Write the 2nd order differential equation of v₁. What should be the value of R (R>0) for this circuit to be critically-damped? 4Ω V₁ www # V₂ IH elem

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Related questions

Q: In a balanced delta connected 30 circuit, the load in each branch consists of a 10 resistance in…

A: Given Data, Line Voltage VL=400 V Frequency f=50 Hz Resistance R=10 ohm Inductance XL=0.0318 H

Q: 15-23. Determine the power density at a point 20 km from an antenna with an input power of 1200 W…

A: It is given that: d=20 kmPI=1200 WApdB=46 dBApdB=10logAp46=10logApAp=3.98×104

Q: 20. Four electricians are discussing wiring under raised floors in information technology equipment…

A: Given, Four electricians are discussing wiring under raised floors in information technology…

Q: V₁ + [-5..5] V e CHAPTER II-4. CONTROL OF MOTOR SPEED ERROR Controller Ge(s) Motor Position (V) Om…

Q: 700 V 0.35 A 0,53 A The total current flowing in the circuit in Figure 5-9 is: • 106 Α 470 Ω Μ 2.82…

Q: 12-12. Determine the characteristic impedance for a quarter-wavelength transformer that is used to…

Q: problems. Show your complete solution in separate sheet of paper (with graph if possible). 1. Three…

A: Electric field is force per unit charge. Gauss law states that total outward flux in closed surface…

Q: Explain how a timing circuit works and list some applications.

A: Timing circuit : Timing circuit is a electronic circuit which synchronize any signal with the help…

Q: Consider a Bank with a floor area of 105sq.m. Solve for the load current rating of the branch…

A: Given information: The floor area is A=105 cm2. Place is bank. We need to calculate the load current…

Q: Which of the following is true about all series ac circuits?(a) The voltage across any circuit…

A: It is given that:

Q: KINDLY ANSWR IMMEDIATELY, THANKYOU FOR HELPING OUT How many 160 ohm resistor in parallel are…

Q: 4. Find the resistance of 800 m of copper cable of cross- sectional area 20 mm². Take the…

A: Given, Length of copper cable, l = 800 m Cross-sectional area, A=20 mm2 The resistivity of copper,…

Q: Q1) Consider a two point charges Q1-1 nc at (1,2,3), and Q2= 2nc at (2, 30, 90) in free space. Find:…

A: Solution is attached with this notes. Thank you.

Q: Write specifications details of all types of wiring/ cables

A: Electrical wiring A method of connecting different accessories for electrical energy distribution…

Q: Q3.A. A TV station is transmitting 10 kW of power with a gain of 15 dB towards a particular…

A: We need to find out electric field at given point due given power

Q: 12.a. Section ___ requires seals to be installed in a raceway system whenever the raceway changes…

Q: 9. Which of the following equation represents mass semiconductors in electronic circuits? action law…

A: The correct option along with the explanation is provided in the following section.

Q: Explain the types of insulator used in overhead transmission and distribution lines and mention…

A: As overhead insulation, transmission lines can utilize one of five different types of insulators: 1.…

Q: electrical what is the disadvantages of potential transformer ?

A: Potential transformer : The definition of a potential transformer is a device used to transmit…

Q: List the equipment in detail with rating for substation and swictchgear installation.

A: It is asked to list out the equipment required for substation and switchgear installation with the…

Q: 10. A capacitor is connected across a 120 V, 60 Hz supply. An ammeter indicates 5 A and a wattmeter…

A: Since you have posted the questions with multiple subpart so we are supposed to answer 3 subpart.

Q: A 10 V, 1 kHz ac source is connected to a parallel circuit consisting of a 470 2 resistor and a…

A: The required parameters can be calculated by using the impedance and input current of the circuit.

Q: Q6:- For the system in Fig. 5: a) Find Pr, Qr. Sr, Vr and the power factor Fp. b) Draw the power…

A: Given figure,

Q: Using JK flip-flops:1. Design a counter with the following repeated binary sequence: 0,1, 2, 3, 4,…

A: The counter can be designed with the help of three JK flipflop. The state transition table should be…

Q: Jw/2 sinc (w/2) Oxx (W) = e Hint: sin 1/2 [ee] Rxx (1) 1 1

A: Solution- ϕxxω = ∫-∞∞Rxxτe-jωτdτ =∫011.e-jωτdτ = e-jωτ-jω01 =…

Q: write the factor governing height of pole

Q: R1 = 10kΩ Rf = 2kΩ. Record the amplitude of the signal source (vg), the ac component of the output…

A: Given: The partial gain for Vg is -2 ±10% R2 = 1kΩ R1 = 10kΩ Rf = 2kΩ

Q: VD А. Given the following circuit in Figure ww 5 ΚΩ determine whether the Diode is conducting or…

A: Given data The given circuit R1=5 kΩR2=10 kΩR3=1000 Ω=1 kΩV1=20 V V2=15 V

Q: 4. Which of the following is the correct relationship between temperature (T) and mobility (u) of…

A: The correct option along with the explanation is provided in the following section.

Q: 7. Two single-phase transformers work in parallel on a load of 750 A at 0.8 p.f. lagging. Determine…

Q: 15-19. Determine the directivity in decibels for an antenna that produces a power density P = 4…

Q: What type is a suitable electrical vehicle based on power systems and machines for human…

A: It is asked which is most suitable electrical vehicle based on power systems and machines for human…

Q: 4. Derive the Characteristic Table, the Truth Table and the characteristic equation of the following…

Q: A 3-phase, 20 MVA, 10 kV alternator has internal reactance of 5% and negligi resistance. Find the…

Q: 2-What is the maximum allowed frequency of the input information signal (modulator) in an AM system…

A: In this question, We need to determine the maximum allowed frequency of the input signal? We know…

Q: Suppose, that in an attempt to increase range, cordless telephone manu- facturers double the power…

A: Cordless telephones communicates using high frequency bandwidth that are allocated for this use. The…

Q: what is servo motor ? is with work with dc

A: Servo motors are a special class of motors that are used for precise angular control, it is a…

Q: le (mA) VCE -7.5 V Vcc=24V Rc {2.5 k Re 1.Sk 90 μ.Χ. 10 80 µA 70 μ.Χ. 60 μA 15 50 µA 25 µA 40 μA 30…

A: The characteristics shows are the output characteristics of CE configuration of a BJT. Q-point is…

Q: conditions

A: So the correct option is option "A"...

Q: An 11 kV, 100 MVA alternator is provided with differential protection. The percentage of winding to…

Q: draw single line diagram of 66 kv substation with explanation and not copied from anywhere

A: 66 kV substation Important function of substation is to collect energy transmitted at high voltage…

Q: 8. MIMO was initially developed in the year

A: The correct option along with the possible explanation is provided in the following section.

Q: An EM wave progating in a certain medium is described by E = 31 sin(3922.8 x 10°t - 9.2x) az V/m…

A: Given: EM wave E=31sin3922.8×106t-9.2xaz V/m

Q: Draw the logic diagram corresponding to the following Boolean expressions without simplifying them:…

A: The given Boolean expression can be implemented by using the OR, AND and NOT gates.

Q: In a short circuit test on a circuit breaker, the following readings were obtained on single…

A: Given in a short circuit test on a circuit breaker following readings, Time to reach the peak…

Q: DIFFERENTIAL EQUATION with POWER SERIES: y" - xy = 0

A: An accumulation of words of the general form aₙ(x-a)ⁿ is a power series. Power series are functions…

Q: Determine the equivalent impedance and the source current of the circuit as shown in the figure…

A: Steps to solve the circuit 1. first calculate the inductive and capacitive reactances of the…

Q: 10. Find out the depletion width of the following p-n junction diode under equilibrium (zero bias).…

A: Given, Where Eg=Energy band gap between conduction level and Fermi level VBi=Built in potential…

Q: Using TDR, a transmission-line impairment

A: Velocity factor- When electromagnetic signal passes through any medium then the speed of…

Q: i(t) below wi R1 C1 ur.

A: j

Concept explainers

Series and Parallel Circuit

Circuits can be classified as parallel and series depending on the manner in which components are connected to one another and the electrical source. The resultant output of the circuit depends on the electrical component.

Question

Write the 2nd order differential equation of v₁. What should be the value of R (R>0) for this circuit
to be critically-damped?
+1
452
ww
V₂
ΤΗ
# |/ F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a) what is the expected order of thedifferential equation for both Vc(t) & Ic(t) b) Use Combined Constraints (element equations, KVL & KCL, solve system of equations) derivesimplified numerical expressions for both Vc(t) & Ic(t) by solving the differential equation for t ≥ 0s
3. (a) Find the characteristic polynomial, characteristic equation, characteristic roots, and characteristic modes of this system. (b) Find y(t) the zero-input component of the response for t >= 0, if the initial conditions are y(0) = 1 and y'(0)= -2 for [(D^2)+4D+8]y(t) = Dx(t)
Find the solution to the difference equation given below?[?] − 0.25?[? − 2] = ?[?]when the unit-step function ?[?] = ?[?] is applied to this system assuming the initial conditions of ?[−1] = 1 and?[−2] = 0.
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear? For linear systems, write "linear" in the space next to the option. For non-linear systems, write "non-linear" in the space next to the option.
The system whose characteristic equation is given as s3 + 2s2 + Ks + 20 = 0 is asymptotically stable for which K values
When the unit step function is applied to the system input given the block diagram below, the output response takes the value c (0.2) = 0.11 fort = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate
The answer of this question on bartleby is of other parts. This is different question. Don't copy that answer. I already have that. I am posting it for the third time. A. Write the state variable equation(s) B. The system equation(s) you obtained in D are (Circle one choice for each statement): Ordinary Differential Equation(s) True False Linear True False Second Order True False Constant Coefficients True False
3. Consider the following second-order differential causal system: y ̈(t)+6y ̇(t)+8y(t) = 2x(t), x(t) = e−3t u(t), y(0) = 2, y ̇(0) = −6, (here, u(t) = step function) where x(t) and y(t) are the input and output of the system, respectively. Find the natural response yn(t), forced response yf (t), and total solution y(t) of the system.
Compare the performances of the first order system, the overdamped, underdamped and critically damped second order system.
Given the plant transfer function, G(s) = 90/ s(s+4) and H(s) = 1. Obtain (i) characteristic equation (ii) damped frequency of oscillation (iii) damping ratio (iv) settling time (v) delay time
When the unit step function is applied to the input of the system whose block diagram is given below, the output response takes the value c (0.2) = 0.11 for t = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate.
3. As shown in a circuit below for which switch S is kept open for a long time and then closed at t = 0. The simplest dynamic equation (in time domain only) governing the circuit will then be?