Write the machine code (binary code) for the following instructions and identify the instruction format (register immediate or jump) for the instructions. 1) sub $s4, $t4, $v0 2) add $s6, $t6, $v1 3) addi $s7, $t7, 7 4) sw $55, 10($t5) 5) jr Sra # The return address is 12

Write the machine code (binary code) for the following instructions and identify the instruction format (register immediate or jump) for the instructions. 1) sub $s4, $t4, $v0 2) add $s6, $t6, $v1 3) addi $s7, $t7, 7 4) sw $55, 10($t5) 5) jr Sra # The return address is 12

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 3SAT: The time it takes to perform the fetch instruction and decode instruction steps is called the...

See similar textbooks

Related questions

Q: The seven stages of the instruction cycle are shown in the following table. Put each stage in the…

A: 1. the PC (program counter) contains the address of the next instruction to be fetched.2. the…

Q: For the instruction being executed: add $s1, $s2, $t0 use the following delays for each…

A: Explanation: First, read the registers. and, Instruction access memory. and, Decode and register…

Q: A two-word directive The address field of LOAD is saved at position 300, and the address field of…

Q: ($s1) contains (0x12345678). Write at most two instructions to move ONLY the second byte value in…

A: This is how you can do this easily. Note: We are given the data in bytes so de defined the variable…

Q: ter stored a program in their memory unit as shown below. Fill Out the following table with the…

A: Answer: The contents of AC, PC and IR, after the implementation of given program in memory unit of…

Q: A computer has the flowing instruction and integer format. The instruction consists of 4 bits…

A: Let's solve all the 3 parts step by step: Here opcode field is of - 4 bits (0 - 3) Immediate field…

Q: Assume that two numbers: dividend and divisor are saved in memory address M1 and M2 respectively.…

A: Given that Assume that two numbers: dividend and divisor are saved in memory address M1 and M2…

Q: Two word wide unsigned integers are stored at the memory addresses OA00 H and 0A02 H respectively,…

A: The Code for given data is as follows: MOV AX, 0; MOV DS, AX ; MOV BX, 0A10H; MOV DX, [0A00H]; ADD…

Q: Assume the program starts at memory location 00. Show the RTL statements of the fetchexecute cycle…

A: Actually, the register is a used to store the data or information. MAR,MDR,IR,PC are also type of…

Q: Assume accessing the memory would take 1000 ns and accessing the registers would take 1 ns. Compute…

A: Code Snippet#1: MOV EAX, [0x00089871] Moves the value at memory address 0x00089871 to the EAX…

Q: Computer Organization The logical instructions above are not included in the MIPS instruction…

A: According to the information given:- we have to evaluate the mention logical instruction.

Q: Use the register and memory values in the tables below for the next questions. Assume a 32-bit…

A: a) add $t3, $t2, $t1 implies adding the contents of register t1 to the contents of register t2 and…

Q: where R1, R2, and R3 are CPU registers, (R1) is the content of R1, a, ß,7, and are the starting…

A: We have , For each operations of given instruction code segment has number of instructions are:-…

Q: Register Content Data Memory Content wo Ох1006 Ох1000 O×FEB1 W1 ОХАВУА Ox1002 Ox0193 w2 w3 Ох0015…

A: Zero Flag (Z) : After any arithmetical or logical operation if the result is 0 (00)H, the zero flag…

Q: The following instructions are executed on a CPU which has R= 23 and PC = 10 for each instruction.…

A: The Answer is

Q: Write assembly instruction sequence for the following instructions: (a) Load a data at memory…

A: Assembly instructions are used to program microprocessors. It is the low-level programming language.…

Q: For the next two questions, consider the following portion of assembly code, which places two…

A: For the next two questions, consider the following portion of assembly code, which places two…

Q: A computer uses a memory unit with 256K words of 32 bits each. A binary instruction code is stored…

A: To find operation code, the register code part, the address part.

Q: 2. Write an instruction sequence that will initialize the ES register with the immediate value…

A: Q)Write instruction sequences that will initialize the ES register with the immediate value 1020H.…

Q: Use the register and memory values in the table below for this question. Assume a 32-bit machine.…

A: a) The direction given is:- Add X3, X2, and X1 The register value of X1 = 12. The register value X2…

Q: 3. Using the given Instruction Table, write the instruction in hexadecimal number: Get the value…

A: Here we write the instruction and explain it and write it in hexadecimal number Answer a) we use the…

Q: O The highest significant bit is 1, The lowest significant bit is 1 O The lowest significant bit is…

A: Here is the Answer and Explanation

Q: The next three questions refer to the following system: A certain ISA has a 32-bit word size, uses…

A: The Answer is

Q: 1. T/F - if (B)=006000 (PC)=003600 (X)=000090, for the machine instruction 0x032026, the target…

A: Actually, register is a used to stores the data\information.

Q: If R0 = 0x8000 and memory data layout is as below, what are the r1 and r0 register values,…

A: LDR r1, [ro], #4 Here LDR stands for load data from memory into register. [Ro] means the content of…

Q: (b) Suppose that the following instructions are found at the given location in memory. Illustrate…

A: Below I have Provided handwritten solution to the given question:

Q: Identify the contents of the registers, memory location (C070H), and the flags as the following…

A: Assembly Language Programming : Assembly language construct is a low-level programming language for…

Q: b) An 8051 subroutine is shown below: R0, #20H @RO, #0 MOV LOOP: MOv INC RO CJNE RO, #80H, LOOP RET…

A: a) To clear RAM Locations from 20H to 7FH b) MC Bytes Opcodes 1 2 78H 20H 1 2 76H, 00H 1 1…

Q: Assume a CPU with a fixed 32-bit instruction length has the following instruction forma

A: a. Op code + mode = 7 + 5 = 12 bits, leaving 22 bits for the operands. With 3 registers,each uses 9…

Q: A computer has a 256K word addressable memory Module with 16 bits per word. The instruction set…

A: Pipelining can be described as the procedure of accumulating instructions from the processor in the…

Q: Assume that before the instruction is executed, the flags are CF=1, ZF=0 and SF=0 and the Registers…

A: In given problem, we have some flags values and some register contents. We have to perform XOR…

Q: Q: Compute the physical address for the specified operand in each of the following instructions. The…

A: Given:

Q: After the instruction Idr ro, [r1] is executed, what is the content of ro? A. The 8-bit value…

A: content of r0 after the instruction executed

Q: The sum of the data, anti and output dependencies for the following sequence of instructions is 11:…

A: Introduction

Q: 3. Suppose M8=x and M9=y. After each instruction has been executed, what is the content of the…

A: Suppose M8-X And M9=Y. After Each Instruction Has Been Executed:

Q: For this question, use the register and memory values in the tables below. Assume a 32-bit machine.…

Q: For the MIPS assembly instructions below, what is the corresponding C statement? Assume that the…

A: The MIPS assembly line: This MIPS processor's machine code is simply known as MIPS assembly code.…

Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is…

A: Solution:

Q: write ALP, assume Ds= 2400h show the content of register as each the following instruction execute…

A: Introduction write ALP, assume Ds= 2400h show the content of register as each the following…

Q: (b) Suppose that the following instructions are found at the given location in memory. Illustrate…

A: Below I have Provided the handwritten solution of the given question

Q: 2. Consider the initial value of register Stia Ox12345678 and the content of memory location…

A: Consider the initial value of register $t1 is 0x12345678 and the content of memory location…

Q: Q: Compute the physical address for the specified operand in each of the following instructions. The…

A: Given data is shown below:

Q: 1. T/F-if (B)=D006000 (PC)=003600 (X)=000090, for the machine instruction Ox032026, the target…

A: As per bartlby guidelines, only 3 sub questions can be answered.

Q: 1) Write an instruction sequence to decrement the contents of data memory locations 0x10, 0x1 1, and…

A: As per our policy, "Since you have asked multiple questions, we will solve the first question for…

Q: (B)- Choose the correct answer for the following questions (Choose FIVE Only) 1. Assume AL register…

A: 1) Ans:- Option c Assume AL register 7FH, it would become 81H after executed NEG AL instruction. 2)…

Q: 1) For each of the instructions below, assume the initial conditions shown for r3-r5 and the flags.…

A: a) ADCS: The instruction ADCS adds the values specified in the second and third operand and also…

Q: For the MIPS assembly instructions below, what is the corresponding C statement? Assume that the…

A: Actually, registers are used to stores the data/information.

Q: The memory contents of the processor are shown below. The processor starts executing instructions…

A: The given code is:- LDI R0, 1LDI R1, 1LDI R2, 4BN R2, CONTSUB R2, R2, R1BR LOOP QUIT

Q: Two unsigned words integers are stored at the physical memory addresses 00B00 and OOB01…

A: # multiplication Memory Mnemonics. Operands Comment 2000 MOV AX, [00B00].…

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

Write the machine code (binary code) for the following instructions and identify the instruction format (register,
immediate or jump) for the instructions.
1) sub $s4, $t4, $v0
of
2) add $s6, $t6, $v1
stion
3) addi $s7, $t7, 7
4) sw $s5, 10($t5)
5) jr $ra
# The return address is 12

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
Most Intel CPUs use the __________, in which each memory address is represented by two integers.
_____ is a CPU design technique in which instruction execution is divided into multiple stages and different instructions can execute in different stages simultaneously.
If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
1) Write an instruction sequence to decrement the contents of data memory locations 0x10, 0x1 1, and 0x12 by 5, 3, and 1, respectively 2) Write an instruction sequence to subtract the 4-byte number stored in memory locations 0x10-0x13 from the 4-byte number stored in memory locations 0x00-0x03 and store the differ[1]ence in memory locations 0x20-0x23
For the MIPS assembly instructions below, what is the corresponding C statement?Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and$s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. sll $t1, $s1, 2add $t1, $t1, $s6lw $t1, 0($t1)sub $t0, $s3, $s4sll $t0, $t0, 2add $t0, $t0, $s7lw $t0, 0($t0)add $t1, $t1, $t0sll $t0, $s0, 2add $t0, $t0, $s7sw $t1, 0($t0)
Assume the following register contents: $t0 = 0x01234567, $t1 = 0x56781234. Set back to these values back after answering each question. For the register values shown above, what is the value of registers ($t0, $t1, $t2, $t3) after executing each instruction? sll $t2, $t0, 2 and $t3, $t2, $t1
A word in main memory may contain an instruction or a binary number in twos complement notation. Demonstrate that this instruction repertoire is reasonably complete by specifying how the following operations can be programmed: (a) Data transfer: location X to accumulator, accumulator to location x (b) Addition: Add contents of location X to accumulator (c) Conditional branch (d) Logical OR (e) I/O operations
Below is a set of instructions for a three-address machine. Write down the equivalent set of instructions for a 1-address machine and a 0-address machine. SUB R1, B, C ADD R2, D, E MULT A, R1, R2
For the following MIPS assembly instructions what is the corresponding C statement? Assume that variables f,g,h,i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Add comments for each line to describe what each instruction does. addi $t0, $s6, 4 # $t0 = &A+4 = &A[1] add $t1, $s6, $zero # sw $t1, 0($t0) # lw $t0, 0($t0) # add $s0, $t1, $t0 #
Suppose that the following instructions are found at the given location in memory. Illustrate the flow of fetch and execute cycle during processing for both instructions. Assume initially [PC] = 45. Program Counter: 45 Accumulator: 123 Memory Location: Memory Address Content 45 STO 79 46 SUB 80 : : 79 737 80 012 : : Perform instruction 45. Perform instruction 46.
2. For the following C statement, what is the corresponding MIPS assembly code? Assume that the C variables a, b, and c, have already been placed in registers $s0, $s1, $s2, respectively. Use a minimal number of MIPS assembly instructions. a = b + (c − 5); 3. For the following C statement, write the corresponding MIPS assembly code. Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. B[i-j] = A[8]; 4.Translate the following C code to MIPS. Assume that the variables, f,g. h, i, and j are assigned to registers $s0, $s1, $s2, $s3, $s4, and $s4, respectively. Assume that the base address of A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: B[8] = A[i] + A[j]; 5.For the MIPS assembly instructions below, what is the corresponding C statement? Assume that the…