xA mechanical metronome consists ofat a torsion SpringSpring on wich at a 15cmlong Pointer is attached. A weight (m=85g)acan be set for the natural frequency of ametronome is applicableD-m.g.LW₁ =√How langes should the minimum spring constentbe that the metronome still a Scarillakates,When The Weight is fasa Pushed to the end?State your result in N/m

Given: Length of the pointer: →L=15 Cm=0.15 m Mass of the pointer: →m=85 g=0.085 kg And acceleration…

X A mechanical metronome consists of at a torsion Spring on wich at a 15cm Jong Pointer is attached. A weight (m=85g) can be set for the natural frequency of metronome is applicable Wo = D-m.g. L a How langes should the minimum Spring constent be that the metronome still ascarillatates, When The Weight is fase fushed to the end? State your result in N/m

X A mechanical metronome consists of at a torsion Spring on wich at a 15cm Jong Pointer is attached. A weight (m=85g) can be set for the natural frequency of metronome is applicable Wo = D-m.g. L a How langes should the minimum Spring constent be that the metronome still ascarillatates, When The Weight is fase fushed to the end? State your result in N/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
A mass of 12 ks is attached to two springs each of stiffness 4000 N/m and mounted in parallel. What is the natural frequency of the system? Answer: 25.8 rad/s
Question 1. A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
Don't give incorrect solution..A structure is modeled as a damped oscillator having a spring constant k = 30 kip/in and undamped natural frequency = 25 rad/sec. Experimentally it was found that a force of 1 kip produced a relative velocity of 1.0 in/sec in the damping element. Determine: a) The damping ratio §. b) The damped period TD.
Plz give right answer. Calculate critical frequency of a helical spring of wire diameter 10 mm, mean coil diameter 50 mm and number of active coils 12. Take tau = 550MPa , G = 80kN / m * m ^ 2
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
The damped frame was subjected to free vibration at W=1000 kN, u0=L+10cm. If the amplitude measured in the first period is 9 cm and t= L+1s at this time, what is the damping ratio (h), critical damping ratio, damping coefficient (c). L=2
A350 N electronic instrument is attached to a ship deck which vibrates at an amplitude of 1.60 mm at 50 Hz. The instrument is to be isolated from the deck with 4 flexible mounts. Determine combined spring constant of mounts such that the amplitude of vibration of the instrument is no more than 0.13 mm. If the springs are equal wirat is spring constant of each mount. What is static diflection of each mount?
a hydraulic shaft carries a set of pulley wheels at the end. The motor has a moment of inertia of 0.8 kg.m^2. If the natural frequency of torsional vibration is 4.74 Hz, what is the distance between the motor and the pulley wheels in meter if the diameter of the shaft is 15mm and modulus of rigidity is 80 GN/m^2
400 kg machine is placed at the mid span of a 3.2 m simply supported steel beam (E=200\times10^9~N/m2) The machine is observed to vibrate with a natural frequency of 9.3 Hz. What is the size of the beam's cross section if the height is twice as the width, considering that:
A machine tool with mass m = 1000 kg and mass moment of inertia J0 = 300 kg/m² rests on elastic supports, as shown in the figure. If the stiffnesses of the supports are given by k1 = 4000 N/mm and k2 = 3000 N/mm, and the supports are located at l1 = 0.4 m and l2 = 0.7 m, determine the natural frequencies and modal forms of the machine -tool. It's the same as this question but with different numbers: https://www.bartleby.com/questions-and-answers/mjo/ef2f3626-9b98-4f38-81a9-e8c4fee1d1ea?source=intercept
An accelerometer is composed of weight W = 0.042 lb suspended by a spring for which k = 5 lb/in., and the fluid damping factor for the instrument is zeta = 0.65. when used on a machine vibrating at a frequency of 13.647 Hz, the instrument reading for the maximum acceleration is 50 in/sec^2. Determine fhe correct value of the maximum acceleration of the machine.