X Incorrect "he extruded plastic shape will be subjected to an internal shear force of V = 380 lb. Dimensions of the cross section are b = 1.2 in., d = 24 in., c= 1.6 in., and t = 0.16 in. Determine: a) the magnitude of the horizontal shear stress at points A and B. b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.8 in. below the z centroidal axis. c) the magnitude of the maximum horizontal shear stress in the extrusion. y (typ.) A B YC V C b. Answer: a) TA = i 444.32 psi TB = i 601.74 psi b) Tc = i 835 psi c) Tmax= psi 374.7

X Incorrect "he extruded plastic shape will be subjected to an internal shear force of V = 380 lb. Dimensions of the cross section are b = 1.2 in., d = 24 in., c= 1.6 in., and t = 0.16 in. Determine: a) the magnitude of the horizontal shear stress at points A and B. b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.8 in. below the z centroidal axis. c) the magnitude of the maximum horizontal shear stress in the extrusion. y (typ.) A B YC V C b. Answer: a) TA = i 444.32 psi TB = i 601.74 psi b) Tc = i 835 psi c) Tmax= psi 374.7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., d = 4.0 in., c = 2.7 in., and t = 0.19 in. Determine:(a) the magnitude of the horizontal shear stress at points A and B.(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis.(c) the magnitude of the maximum horizontal shear stress in the extrusion
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., D = 4.0 in., C = 2.7 in., And t = 0.19 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion
According to the general shear stress formua, shear stress distribution on a rectangular crosss section is parabolic. When b = 47 mm, h = 79 mm, transverse shear force V = 69 k N, please calculate the max shear stress on the cross section shown below: max (f v max in textbook)= ____ MPa.
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9
Find stress at BD, BE, CE area = 0.0012 m^3
Consider member (1). Use the yield stress, the factor of safety, and the force to calculate the minimum cross-sectional area required for member(1). A1= ? (unit mm^2)
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Determine the average normal stress developed on the cross section as shown inFigure 1.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 52 MPa, Sy = 63 MPa, and Sxy = 29 MPa.(a) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)(c) Compute the absolute shear stress at the point.
Using the equations for determination of stress at a point, calculate the value for the maximum shear stress that develops if the major principal stress is 7.2 ksi compression and the minor principal stress is 3.6 ksi tension.
1. What is the maximum shearing stress (fv) of the beam? (in MPa) 2. What is the maximum flexural stress (fb) of the beam? (in MPa)