The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.65-in.-diameter pin at A, and the 0.31-in.-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5234 Ib. Round off the final answer to two decimal places. 0007 P.png ... 70° 4 in. 3.5 in 30° 0.5-in dia. Detail at A

The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.65-in.-diameter pin at A, and the 0.31-in.-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5234 Ib. Round off the final answer to two decimal places. 0007 P.png ... 70° 4 in. 3.5 in 30° 0.5-in dia. Detail at A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stress of 5-mm radius cable CD that supports the bar AB at 150-kilograms and a 2,000 kg/m² force at point A. Hint: W=m*g
Box A of 200 N starts from rest and slides down from the inclined plane. The rollers are frictionless and the friction force between the box A and the inclined plane is Fs = 80 N. Block B has a weight of 70 N. If the cable strength is T = 35.40 N, what is the speed of the chest A after C = 4 m sliding? Neglect the mass of the pulleys and the cable.
The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.07 m from the pin if P = 499.99 kN.
: The boom AC is a 4-in square steel tube with a wall thickness of 0.25 inch. The boom is supported by the 0.6-in diameter pin at A, and the 0.40-in diameter cable BC. The working stresses are 25 ksi for the normal stress in the cable, 18 ksi for the axial stress in the boom, and 13.6 ksi for shear in the pin. Neglecting the weight of the boom, determine the largest safe load P that can be applied as shown.
ENGINEERING MECHANICS (No lng explanation needed. Write the complet solutions and legibly. Rate will be given) Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively The allowable shearing stress is 1 GPa with F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E. Where: Radius of the gear at B, rB = 100mm Radius of the gear at C, rC = 150mm
A cable is attached to the 20-kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of x1 is 10m, x2 is 8m and h is 18m. Neglecting the weight of the crane. Determine the following. 1. Force at cable AC. 2. Resultant reaction at B. 3. Largest load that can be lifted if the maximum force of cable AC is 50kN.
1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
the cable reel is in contact with the ground at A and wall B with a weight of 100 kg. If the static friction coefficient between the roller and the contact surfaces is Ms = 0.3, find the smallest force P that will cause the roller to rotate.
A 90-lb load is suspended from the hook shown . If theload is supported by two cables and a spring having a stiffnessk = 500 lb/ft, determine the force in the cables and the stretch of thespring for equilibrium. Cable AD lies in the x–y plane and cable AClies in the x–z plane.