Question

Find out the transfer function 

x[n]
Unit
yin]
delay
Expand
Transcribed Image Text

x[n] Unit yin] delay

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Signals and Systems

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: A 4 pole 250 volt shunt motor gives 10kw when running at 1000 rpm and drawing armature and field cur...

A: Given values are - P=4Vt=250VoltN=1000rpmIa=60AISh=1ARa=0.2Ohm Given motor is shunt motor.

Q: (1) A full adder in which:  SUM = C' (AB' + A'B) +C (AB + A'B')   (2) CY = AB + BC + AC

A: The truth table for the given full adder is given as  A B C Sum Carry 0 0 0 0 0 0 0 1 1 0 0...

Q: How far must mechanical protection be provided when underground service conductors are carried up a ...

A: The Underground Conductor are electric conductor insulated and placed under the surface of the earth...

Q: O:28)

A: Part (a): Consider the open-loop transfer function, Gs=s2-2s+4s+5=s-1+j1.73s-1-j1.73s+5 The number o...

Q: what is the power absorbed of two identical resistors are connected in series to 10v source. one res...

A: Given: Two identical resistors with resistance 2-ohms each is connected in series. Source voltage, V...

Q: Lightning strikes a dielectric sphere of radius 15 mm for which e, =4.5, o 5 x 10- S/m and deposits ...

A: Click to see the answer

Q: For the circuit in Figure 1,  and the 9 V source supplies a current of 7.6 A (that is, a current of ...

A: Here we will apply Nodal analysis to find out the unknown parameters.  => In nodal analysis we co...

Q: A 20-ohm resistor and a capacitor are connected in series with a battery of 60 volts. At t 0, there ...

A: Click to see the answer

Q: Emitter stabilized polarization BJT DETERMINE, FIND: a. IBQb. ICQc. VCEQd. Vce. VBf. VE

A: Click to see the answer

Q: A 400V, 50Hz 30hp three-phase induction motor is drawing  current at  power factor 0.8 lagging. The ...

A: The given information of the motor:

Q: a) Construct a circuit model for this device using an ideal voltage source and a resistor.

A: (a)

Q: Consider the circuit shown in Figure 1. Vcc= +12 V (DC), R1 = 100KΩ, R2 = 10 KΩ, RE = 1KΩ and RL = 2...

A: To find all the circuit parameters given the circuit can be modified as From the figure we have 

Q: 4- If we have a signal f(t) passing through a system with impulse response g(t), the output is (b) g...

A: Convert the functions in the Laplace transform, and find the output. f(t)→LFsg(t)→LGsYs=FsGs

Q: Find the Laplace transforms of the following time functions. using the Laplace transform definition ...

A: Click to see the answer

Q: In the circuit given below, R = 10 Ω. Find vo using mesh analysis.  The value of vo in the circuit i...

A: d

Q: 4. Indicate if the power thyristor will be on or off under the following conditions: The thyristor w...

A: Click to see the answer

Q: Find I and V in the given circuit. Assume A = 4 A, B = 11 A, and C = -5 A.   The current and voltage...

A: Click to see the answer

Q: Q:22)

A: Click to see the answer

Q: Answer the following questions: i. If a 3-input XOR gate has eight input possibilities, how many of ...

A: (i) 3 input X-OR gate symbol present as, Where output, w=x⊕y⊕z  

Q: a sine wave has a maximum value of 230 v. what is the voltage after 38° of rotation

A: Click to see the answer

Q: 2 A sequential circuit has two JK flip-flops A and B and one input x . The circuit is described by t...

A: Click to see the answer

Q: 4.2 Use the node-voltage method to find v in the circuit shown. 6 N 20 4Ω 4.5 A $10 12N (*) + 30 V

A: Click to see the answer

Q: In the circuit given below, R = 110 Ω. Find the value of io using mesh analysis.    The value of io ...

A: Consider the voltage across the current is vo.  The circuit diagram in which the current is mentione...

Q: Vdd value is 12V. Figure 1 Problem 2: Determine the following for the network of figure 2 given that...

A: Click to see the answer

Q: Determine the currents I1, I2 and Iz for the electrical network shown in the following figure:

A: Write KVL in both loops,   50-5I1-20I3=0         .....130+20I3+10I2=0      ......2                  ...

Q: R:57)

A: X1 is the overlap angle μVs=Vmsin ωtVs=2202 sin ωtVm==2202 ∆Vd0 = The average voltage reduction due ...

Q: A dc power supply is to be developed by employing an ac to dc converter as a power processing conver...

A: According to question: The suitable rectifier for above power processing will be single phase semi-c...

Q: 1. The current entering the positive terminal of a device is, i = 2e-2t (A) and the voltage across t...

A: Click to see the answer

Q: In the circuit given below, V = 174 V. The variable resistor is adjusted until it absorbs maximum po...

A: As per maximum power transfer theorem, maximum power absorbed by load resistor if the load resistanc...

Q: an overhead transmission line has a span of 220 meters the conductor waiting 0.604 kg/m.What will be...

A: Given: Span, L=220 m Weight of conductor, w=0.604 kg/m Tension, T=2879 kg

Q: b) Obtain the output expression Y for the circuit given in Figure 2 (Write the output of each gate)....

A: Click to see the answer

Q: Determine IB RC 100 Ω RB + Vcc 10 V 10 kΩ VBB 5 V

A: Click to see the answer

Q: a) Determine the number of mesh-current equations needed to solve the circuit shown. 4.8 b) Use the ...

A: Given circuit,

Q: Write one paragraph describing why you think chrome has a shiny surface.

A: Most metals are shiny like chrome when you polish them. However, they usually quickly oxidize when t...