i need the answer quickly Problem 6.9. Draw the shear force and bending moment diagram for a simply supportedbeam of length 9 m and carrying a uniformly distributed load of 10 kN/m for a distance of 6 mfrom the left end. Also calculate the maximum B.M. on the section.Sol. First calculate reactions R and Rg-10 kN/mB6 m(a)RA9 mR40 kN20 kNBase lineRA (b)40(b)AS.F. diagramF20M = + RA.x-w.x.ParabolicParabolicStraightline(c)80AB.M. diagramBase lineFig. 6.28

Answered: Image /qna-images/answer/d037d9c0-368a-4505-915e-7ab59910f774.jpg

Answered: y distributed load of 10 kN/m for a di…

Engineering

Mechanical Engineering

y distributed load of 10 kN/m for a di um B.M. on the section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the magnitude of the pin force at A. Modification: Change the load to 3,50 Ibs, the…

Q: Dotermine all for ce of mem bers the truss Showwn

Q: PROBLEM 10.13 Determine the radius of the round strut so that the round and square struts have the…

A: Given that, E==200 GPaE=200×103 N/mm2Side of the square strut=a=25 mm,Length of the strut, L=1m…

Q: Determine the critical buckling load for a column that is pin supported?

A: Consider the diagram shown below for a hinged column.

Q: For a column, determine the factored design load, P., when the column ha

A: given:dead load Wd=120klive load WL=64klive roof load WLR=19KSnow load Ws=25k

Q: If the length of a column is doubled, the critical load becomes ?

Q: There are 3 plans (a-c) of bolts group design, where R, a and L keep constant, a=60mm, and L=300mm.…

Q: square aluminum bar is to support a load of 40 kN on a length of 3 m. ssuming pinned ends, determine…

Q: e vessel, as shown in the bolts along with rer plate thickness. e tensile stress for MPa and for…

A: solution of Question 1

Q: A dynamic load of F = 25 kN is exerted on a cy- lindrical pressure vessel. If using 4 distributed…

A: Given data: The dynamic load acting on the bolts is F = 25 kN = 25000 NThe number of screws is n =…

Q: C ):- Draw the MC stress elemen Find:-

A: given:σX=20ksiσy=14ksi

Q: A square column with an f'c = 4.0 ksi, Grade 60 Re-bar supports a Compressive Load equal to 600…

Q: PI-2. In cach case, determine the largest internal shear force resisted by the bolt. Include all…

Q: toed et hing ? hing= 20 KN/m

Q: A 400lmill squar Assume column to be short and that any moment caused by the loads can be neglected.…

A: Given Data Size of the column is : Ag=400×400 mm=160000 mm2 Live load is : L.L=790 kN Dead load is…

Q: ructural support for a machine will be subjected to a static tensile load of 16.0 kN.Specify…

Q: arked a---a. Just at this si

A: given:

Q: Problem 2. A chord, with its supports at A and B, bears a load of 10 KN and a load of W. What should…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer a single question. Kindly…

Q: Q.2 Determine the vertical movement at C, if (P-100 kN). Steel Le 2m A-300 me E-200 GPa 2m

Q: A 3 × 16 rafter cantilevers over a 3 × 16 support beam. If both members are of Hem Fir, No. 1 grade,…

A: Given that A 3 × 16 rafter cantilevers over a 3 × 16 support beam. The rafter load on the support…

Q: to the ght rigid bar are identical except for ength. Before the load W = 6500 lb. ras attached, the…

Q: (a) Sketch a free body diagram for each steel grating that includes the mass's action and reaction…

A: As per honor code and answering guidelines I can answer 1st three subparts at a time.If you want…

Q: Required: Stress in the left rod after its lower end is attached to the support.

Q: b- 10 mm diameter of Brinall hardness ball when the load 500 kgr and HB= 300 determined the diameter…

A: Given: Diameter of the ball=10mmBrinall hardness =300Loading=500kg.f

Q: ed by a ball-and-socket joint at D and short each member and state if the members ar if the mer

Q: Q43-Method 4 Sections eokn 40 ka loola VG VK M 8. "RB Delermine the force in members GJi Jk, HI, IL,…

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

Q: Determine the Support reoctions. /Point A ro (ler support and Point B is a pinned is gN 6 NIm

Q: 0.10-in radius T 2.00-in dia. 1.25-in dia. Applied torque 2200 lb-in

A: GivenT=2200lb-inD=2ind=1.25inr=0.10in

Q: Determine all member forces. Using the Method of Joints.

Q: Determine the radius of the round strut so that the round and square struts have the same…

A: Given data: The young’s modulus, E = 200 GPa. Calculate the area of the square struts. A=25 mm×25…

Q: A square aluminum bar is to support a load of 40 kN on a length of 3 m. Assuming pinned ends,…

A: Given that: Cross section of the bar is a square. Let a = length of each side in mm. l = length of…

Q: a. The change in length of rod EF b. The stress in each rod.

A: For solution refer below.

Q: If the length of a column is doubled, the critical load becomes?

A: Given Data⇒ Length of column=L If L=2L Critical load(P1)=?

Q: Meckenieal Design EnginziNG Calculate the maximum tensile stress in the bracket as shuwn beln. G0 mm…

A: L=400 mmCross section =80 mm×20 mmAxial load P=4.2×sin40°=2.6997 KNTransverse load…

Q: e the axial load of spiral column with respect to first and sece

A: the values and figure given in the question are as follows:- characteristic strength of…

Q: POINT ERD 21,000 400 H UNIPORM LOAD A 16' 以 R2

A: Given: To find: R1 and R2

Q: rmly distributed l a point load of 3 cantilever.

A: Shear Force: From x=0 to x=2 SF= 3 KN (Constant) From x=2 to x= 4m at any cross section SF= 3+5x'…

Q: - Compare the critical stresses using E Rankine's formulae for struts with sle ratios, 50, 100, 150…

Q: What is the equivalent concentrated load of a triangular load which varies from 0 at one support and…

A: Free body diagram of the beam is, The point load acting on the beam is P=12×6 m×9 kN/m=27 kN

Q: B 4 ft C. E D 20 kips 5 ft- -5 ft-

Q: Shown in Fig. P-255 is a section through a balcony. The total uniform load of 600 kN is supported by…

A: We have given

Q: Describe the Moment Arbitrarily Applied?

A: Moment The moment can be termed as the quantity, which is the product of the displacement, and the…

Q: factor of safety for this loading is

A: Given data; A ductile material having an ; Endurance limit=196 N/mm2Yield point=294 N/mm2Max.…

Q: The approximate relationship between endurance limit of rotating beam specimen (S'e) and ultimate…

A: Relationship between endurance limit and ultimate tensile strength for cast iron. The relation is…

Q: wwwwm Critically evaluate the deformation of the bar shown under the given loads.

A: first of all draw free body diagram of each bar and then perform calculations accordingly.

Q: A book is to be mounted on a wall as shown. Weight,W, is 2000N. Shear stress in the bolts should not…

A: Given data: ◆ The weight of the book: W = 2000 N ◆ The allowable shear stress in the bolt: τallow =…

Q: Determine the stress

A: To find stress and strain in bar and elastic modulus.

Q: Calculate the slope at supports, if the area is 180 kNm2. Take flexural rigidity as 50000. *

Q: 117 kN/m A Hinge Hinge 5m im

A: Given Data :-

Question

i need the answer quickly

Problem 6.9. Draw the shear force and bending moment diagram for a simply supported
beam of length 9 m and carrying a uniformly distributed load of 10 kN/m for a distance of 6 m
from the left end. Also calculate the maximum B.M. on the section.
Sol. First calculate reactions R and Rg-
10 kN/m
B
6 m
(a)
RA
9 m
R
40 kN
20 kN
Base line
RA (b)
40
(b)
A
S.F. diagram
F20
M = + RA.x-w.x.
Parabolic
Parabolic
Straight
line
(c)
80
A
B.M. diagram
Base line
Fig. 6.28

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A where they enter the ground and they are supported by horizontal struts whose center lines are 10 m above A. The piles are spaced 1 m apart between centers and the depth of water against the dam is 10 m. Assuming that the thrust in the strut is two-sevenths the total water pressure resisted by each pile, sketch the form of the bending moment and shearing force diagrams for a pile. Determine the magnitude of the bending moment at A and the position of the section which is free from bending moment. (Cambridge). i. 238 kN-m; 0.75 m from A. ii. 238 kN-m; 0.75 m from B.
Draw the shearing-force and bending-moment diagrams for the following beams: 1. A cantilever of length 20 m carrying a load of 10 kN at a distance of 15 m from the supported end. 2. A cantilever of length 20 m carrying a load of 10 kN is uniformly distributed over the inner 15 m of its length. 3. A cantilever of length 12 m carrying a load of 8 kN, applied 5 m from the supported end, and a load of 2kNlm over its whole length.
Draw the shear and bending-moment diagrams for a simply supported beam AB of span L subjected to a single concentrated load P at its midpoint C
Draw the bending moment and shear diagrams for bar CD of the structure below.
Draw the Shear Force and Bending Moment Diagram for the loaded cantilever beam of length AE, 8 m long shown below. Ignore the self-weight of the beam, Take, AB = 2 m, CD = 2 m, DE = 3.5 m.
For the beam and loading shown, draw the shear and bending-moment diagrams. Use methodof sections.
The simple beam AB, shown below, supports a concentrated load of 6 kN and a segmentof non-uniform load of intensity varies from 1 kN/m to 3 kN/m at point B.a- Determine the shear force and bending moment at a cross section located 3m from the leading edge A.b- Draw the shear force and the bending moment diagrams for the beam.
Draw the influence lines for the vertical reaction and the reaction moment at support A and the shear and bending moment at point B of the cantilever beam shown in Fig. 8.4(a)
A car parking roof with cantilever beam of length 6 m carrying point loads of 12 kN and8 kN at 1.5 m and 2.5 m respectively from the free end and the point loads of 6 kN,3 kNand 4 kN acts at 1.5 m, 2.5 m and 6m from the fixed end. Construct the shear force andbending moment diagram for the beam and also identify the point at which the maximumshear force and bending moment is acting on the beam.
5.82 The simply supported wood beam, fabricated by gluing together fourwooden boards, carries the three concentrated forces. The working bending and shear stresses for the wood are 1000 psi and 600 psi, respectively. Determine the largest allowable value of the force P.
NO. 4 Given the beam shown with computed reactions and a cross section. Determine the Maximum horizontal shear stress on the section.
Select the lightest-weight wide-flange beam from Appendix B that will safely support the loading shown. The allowable bending stress sallow = 24 ksi and the allowable shear stress of tallow = 14 ksi.