yauges system mounted at a point on a structural member that is subjected to multiaxial stresses, where we have the following readings: Ex = 6.686 x10-4; &y = 3.0 x10-4; ɛz = - 6.857 x10-5; %3D %3D Yxy 2.580 x10-3; !! Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and Poisson's ratio v = 0.29;

yauges system mounted at a point on a structural member that is subjected to multiaxial stresses, where we have the following readings: Ex = 6.686 x10-4; &y = 3.0 x10-4; ɛz = - 6.857 x10-5; %3D %3D Yxy 2.580 x10-3; !! Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and Poisson's ratio v = 0.29;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.
A strain gauge is used to measure the tension force in a 2-cm diameter bar of steel with Young modulus of 2.07 x 107 N/cm2 (30 x 106 lb./in.2). The strain gauge has a nominal resistance of 160 Ω and a GF of 5. The gauge is connected to a bridge supplied with a 10 Vdc. The bridge was initially balanced. After the bar is put under tension, the bridge output voltage is 0.0008 Vdc. Draw the schematic of the bridge (setup). Calculate the force on the bar.
A resistance, wire strain gauge with a gauge factor of 3 is bonded to a steel structural e subjected to a stress of 200 MN/m² The modulus of elasticity of steel is 400 GN/m² Calculate the % change in the value of the gauge resistance due to the applied stress
Consider a Wheatstone bridge circuit that has all resistances equal to 100 Ω. The resistance R1 is a strain gauge that cannot sustain a power dissipa- tion of more than 0.25 W. What is the maximum applied voltage that can be used for this bridge circuit? At this level of bridge excitation, what is the bridge sensitivity?
A pressure difference of 35 pa is available to force -10c air. through a circular sheet metalduct 400 mm in diameter and 20m long. Find thevelocity in m/s. A.11.64 B.38.20 C.12.81 D.20.60 SHOW DETAILED SOLUTIONS
A bar of 50 mm diameter is subjected to a axial Pull of 65 kN. The measured extension on gauge length of 170 mm is 0.25 mm and change in diameter is 0.003 mm. Calculate: (i) Young’s Modulus, (ii) Poisson’s ratio (iii) Shear Modulus. and (iv) Bulk Modulus (i) The Young's modulus is (N/mm2) = _________________ (ii) Poisson's ratio = ___________________ (iii) The shear modulus is (unit in N/mm2) = ________________ (iv) The Bulk modulus is (unit in N/mm2) = ________________
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.
i. If you know that any strain gauge has a sensitivity towards temperature.In other words, any change in the temperature could also affect theresistance value. How can we get a correct reading from strain gaugesand get rid of the temperature effect?ii. In an AC LVDT system, measuring the output voltage alone gives anindication of the displacement from the center, but not the direction ofdisplacement. Explain why, and also explain a method for solving thisproblem.iii. In a vortex flow meter, there are many methods that could be used tomeasure the effect of vortices and measure the flow rate. Explain howvortices could occur in this flow meter, and explain three methods thatcould be used for measuring the effects of vortices in a vortex flowmeter.iv. Explain in details how can we use a capacitor to indicate the lever ofwater in a tank (use drawings and electrical diagram to elaborate on yourexplanation).Page 5 of 63v. Bimetallic strip could be used as a temperature detector. Explain…
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph.
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph. Answer: breaking stress,true stress at fracture and limit of proportionality.
A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length of the pipe is L = 5.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - ____ mm Inside diameter - ____ mm Lenght - ____ mm standard coefficient of thermal expansion steel: 11.25x10^-6/degrees
A single electrical resistance strain gauge of resistance 100 ohm and having a gauge factor of 2.5 is bonded to a metal having an elastic limit stress of 300 kN/m² and modulus of elasticity of 250 GN/m2 Calculate the change in resistance due to a change in stress equal to 1/20 of the elastic range of metal