You are asked to design a small wind turbine (D=x+1.25 ft, where x = 22). Assume the wind speed is 15 mph at T-10°C and p=0.9 bar. The efficiency of the turbine is n = 25%, meaning that 25% of the kinetic energy in the wind can be extracted. Calculate the power in watts that can be produced by your turbine. I

You are asked to design a small wind turbine (D=x+1.25 ft, where x = 22). Assume the wind speed is 15 mph at T-10°C and p=0.9 bar. The efficiency of the turbine is n = 25%, meaning that 25% of the kinetic energy in the wind can be extracted. Calculate the power in watts that can be produced by your turbine. I

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 48P

See similar textbooks

Similar questions

A vertical cylindrical tank with diameter 2 m and height 5 meter is full of water. How much work is required to pump all the water to the top of the tank? Use 1000 kg / m3 for the density of water and 9.8 m /s2 for the acceleration due to gravity. (Volume of a cylinder: v =pir^2h )
Using the work and energy relations, solve for the constant force “P” required for a system consisting of three blocks given in the figure to have a velocity of 5 m/s when it is moved 2 m after it is released. The friction coefficient between the blocks and the surface is 0.3, and the rollers will be assumed to be frictionless. The weights of the reels are WA=400 N, WB=1000 N and WC=200 N.
Water flows through the turbine shown at a rate of 0.386 m3/s. The pressures at points A and B are 161.2 kPa and -19.6 kPa, respectively. What is the electrical power generated by the turbine if it is 85% efficient?
A sluice gate, as shown in Figure Q1, is used to control the upstream water level in a4 m wide rectangular channel. The water discharge in the channel is 12 m3/s. Given the water depth at 1 is 2.4m use the Specific Energy equation to findthe water depth (to 1 decimal place) at 2.
A liquid of specific gravity of 1.75 flows in a 6 cm horizontal pipe. The total energy at certain point in the flow is 80 J/N (joules/newton). The elevation of the pipe above the fixed datum is 2.6 m. If the pressure is 75 kPa. Determine the velocity of flow in m/s. A.23.86 b.32.45 c.37.85 d.42.25l
The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 6 MW when the shaft rotates at 22 rad/sec. Determine the angle of twist in the shaft in radian. G = 75 GPa.
In Fig.2, A Pelton wheel has a mean bucket speed (U) of 89 m/s with a jet of water flowing at the rate of 1 m3/s under a head of 270 m. The buckets deflect the jet through an angle of 170º. Calculate the power delivered to the runner and hydraulic efficiency of the turbine. Take Cv = 0.98 , V= Cv root of 2gH , workdone per second by the jet on the runner = ρaV1 (Vw1 + Vw2) x U and Hydraulic efficiency ηh = 2 U (Vw1 + Vw2)/V12
The flow rate of the hydroelectric power plant in the figure is 50 m3/s, and 2 meters of water column energy loss occurs due to friction in the pipeline. Find the power that water transfers to the turbine. Calculate the theoretical and actual power of the turbine by taking the efficiency of the turbine-generator group, η = 0.92. (Answer: Ntheoric=52 MW and Nreal=48 MW)
The flow rate of the hydroelectric power plant in the figure is 50 m3/s, and 2 meters of water column energy loss occurs due to friction in the pipeline. Find the power that water transfers to the turbine. Calculate the theoretical and actual power of the turbine by taking the efficiency of the turbine-generator group, η = 0.92. (Answer: ?theoric=52 ?? and ?real=48 ??.)
Water flows from an upper reservoir to a lower one while passing a turbine as shown. 1. Compute the total head loss due to friction when the discharge is 150 lit/s. a. 4.25 m b. 3.84 m c. 5.67 m d. 2.54 m 2. Find the velocity of water. a. 2.05 m/s b. 4.12 m/s c. 3.06 m/s d. 6.57 m/s 3. Find the power input of the turbine. a. 213.5 kW b. 210.6 kW c. 115.2 kW d. 356.2 kW
The crank and connecting rod of a theoretical steam engine are 0.4 m and 1.6 m long, respectively. The crank makes 180 rpm in clockwise direction. When it has turned 45° from the inner dead center position, determine the: a) Velocity of piston, b) Angular velocity of connecting rod
Paolo owns a hydroelectric power generating system as shown in HG008. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 150 lps. The total length of pipe connecting the two reservoir is 100 m. The pipe diameter is 250 mm and the Hazen – Williams coefficient is 120. The water surface elevations of reservoirs 1 and 2 are 197 m and 50 m, respectively. 1. Find the frictional head loss in the pipe in m. 2. Determine the power generated by the turbine in kW. Neglect minor losses.