You are designing a device that will change the direction of an incoming beam of electrons by 90 degrees (from +x to +y). You plan on doing so by shooting the beam into a square region of uniform magnetic field, as shown in the figure (qfig2.png) below. The incoming speed of the electrons is v=5×10 m/s, and they enter the region of uniform magnetic field 10 cm from the top of the region. Find the magnetic field strength in microteslas needed to deflect the particles by 90 degrees. Again, give your answer in microteslas to 1 decimal place. 10 cm B

You are designing a device that will change the direction of an incoming beam of electrons by 90 degrees (from +x to +y). You plan on doing so by shooting the beam into a square region of uniform magnetic field, as shown in the figure (qfig2.png) below. The incoming speed of the electrons is v=5×10 m/s, and they enter the region of uniform magnetic field 10 cm from the top of the region. Find the magnetic field strength in microteslas needed to deflect the particles by 90 degrees. Again, give your answer in microteslas to 1 decimal place. 10 cm B

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter24: Electromagnetic Waves

Section: Chapter Questions

Problem 53P

See similar textbooks

Similar questions

(a) What is the velocity of a beam of electrons that goundeflected when passing through crossed (perpendicular)electric and magnetic fields of magnitude 1.88 x104 V/mand 2.60 x10-3 T respectively? (b) What is the radius ofthe electron orbit if the electric field is turned off?
Assuming the radius of the circular path of the electron is 4.9cm when voltage is 100v and coil current is 1.4 A and The Helmholtz coils have 130 turns and a radius of 15 cm. With N=130 and R=0.15 If the current in the Helmholtz coils were 1.4 A, rather than 1 A, and the accelerating voltage were still 100 V, what would the radius of the electron's path be? Give your answer in cm, and enter only the number. Blackboard will accept an answer witin 20% of the value it expects.
What is the velocity of a beam of electrons that goes undeflected when moving perpendicular to an electric and magnetic fields. E⃗ E→ and B⃗ B→ are also perpendicular to each other and have magnitudes 4900 V/m and 6.7×10−3 T , respectively. What is the radius of the electron orbit if the electric field is turned off?
The deflector plates of a Thomson appliance are 6.0 cm long and separated by 1.2 cm. The distance between the front edge of the plate and the tube is 30.0 cm. The energy assigned to the electrons of the beam is 2.8 keV (can make an illustration for a good understanding) (a) If the potential of 25 V is applied to the deflector plates, what will be the deviation of the beam on the screen? (b) Find the module of the crossed magnetic field that would allow the beam to pass through the plates, without suffering any deviation. Answer a) 7.36 mm b) 6.64 x 10^ - 5 T
Assuming that the current is 1A and radius of the circular path of the electron is 4.9 What is the magnetic field where the electrons are traveling that results from this 1 A current in the Helmholtz coils? Hint: Evaluate the expression given for the field betwee two Helmholtz coils with the dimensions used in the experiment. Provide a numerical answer with no units, simply the field in "microtesla", that is in 10-6 T. For example, if you found 3.4 x 10-4 T, answer "340".
What is the speed of a beam of electrons (in SI units) that go undeflected when passing through crossed electric and magnetic fields of magnitude (5.07x10^0)x104 V/m and (4.270x10^0)x10-3 T, respectively? Give your answer to 3 sf.
Consider a uniform magnetic field of magnitude 0.2 T which is directed along the direction of the positive x axis. A positron, which was accelerated by a potential difference of 1 kV, enters this region of the magnetic field with a velocity v which forms an angle of 85 with the x axis. For this case in which the path that the positron describes is helical, as shown in Figure 1, determine:a) The radius r of the helical path.b) The pitch p of the helical path.
What is the direction of a current that experiences themagnetic force shown in each of the three cases in Figure22.54, assuming the current runs perpendicular to B ?
The potential difference V(t) between parallel plates shown above is instantaneously increasing at a rate of 107V/s. What is the displacement current between the plates if the separation of the plates is 1.00 cm and they have an area of 0.200m2?
An electron entering Thomson’s e/m apparatus has an initial velocity (in horizontal direction only) of 4.0 x 106 m/s. In the lab is a permanent horseshoe magnet of strength 12 mT, which you would like to use. (a) What electric ﬁ eld will you need in order to produce zero deﬂ ection of the electrons as they travel through the apparatus? (b) The length of nonzero E and B ﬁ elds is 2.0 cm. When the magnetic ﬁ eld is turned off, but the same electric ﬁeld remains, how far in the vertical direction will the electron beam be deﬂected over this length?magnetic ﬁ eld is turned off, but the same electric ﬁ eld remains, how far in the vertical direction will the electron beam be deﬂ ected over this length
Given the following massspectrometer schematic, find theB-field such that the radius of theparticle’s trajectory is 0.194 m. Assume the particle is an electronwith mass 2.36 x 10-26 kg, and beginsits trajectory in an E-field of 2.1 x103 V/m.
The potential difference V(t) between parallel plates shown above is instantaneously increasing at a rate of 107 V/s. What is the displacement current between the plates if the separation of the plates is 1.00 cm and theyhave an area of 0.200 m2 ?