You are the mechanical engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe?

You are the mechanical engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

Thermodynamics Answer the following problem with complete solutions. Write legibly A balloon is filled with pure oxygen at 10 ℃. The balloon is released from the bottom of a water-filled testing pool and floats 30 m to the water surface (where the atmospheric pressure is standard). The volume of the balloon is 3,000 cm^3. The temperature is 25 ℃ at the surface of the water, and the water temperature at the bottom of the pool is 10 ℃. What is the volume of the balloon at the surface after it has come into thermal equilibrium with the surroundings
The heat transfer between a solid body and a fluid medium is determined by the equation Q=h·A·(Ts-Tf). Here; Q is the amount of heat transferred, h is the heat transfer coefficient, A is the heat transfer surface area, Ts is the temperature of the surface and Tf is the temperature of the fluid. These parameters were measured as h=250±1.75 W/m2ºC, A=20±0.75 m2, Ts =100±0.75ºC and Tf =25±0.75ºC, including error levels. What is the total uncertainty in the amount of heat transferred, in ±%? a. 3.98 b. 4.07 c. 2.73 d. 2.95 e. 3.88
The speed of sound traveling through the sea is a function of temperature, salinity, and pressure. It is modeled by the function C = 1449.2 + 4.67T -0.055T² +0.00029T³ + (1.34-0.01T) (S-35) + 0.016D where C is the speed of sound (in meters per second), T is the temperature (in degrees Celsius), S is the salinity (the concentration of salts in parts per thousand, which means grams of dissolved solids per 1000 grams of water), and D is the depth below the sea surface, in meters. Calculate the following (Check attached image d3) when T = 10 °C, S = 35 parts per thousand, and D = 100 m. Explain the physical meaning of these derivatives.
An airplane builder wants to build a scaled-down model of a real airplane in a 12:1 ratio in order to be able to perform tests in a wind tunnel. The real plane flies at 126 km/h, while the air speed in the tunnel where the model is located is given by V. The performances of the two will be equivalent for a value of V, in m/s, equal to Data: air viscosity η = 1.8 × 10-5 kg/(m.s) air density ρ = 1.3 kg/m3
Fluid runs through a drainage pipe with a 10-cm radius and a length of 30m (3000cm). The velocity of the fluid gradually decreases from the center of the pipe toward the edges as a result of friction with the walls of the pipe. For the data shown, v(x) is the velocity of the fluid (in. cm/sec) and x represents the distance (in. cm) from the center of the pipe toward the edge. x 0 1 2 3 4 5 6 7 8 9 v(x) 195.2 194.7 193.7 192.3 190.6 188.4 185.8 182.8 179.5 175.7 Use regression to find a quadratic function to model the data. Use all of the given data points and round each coefficient to 4 decimal places.
The following data are given for a biogas digester suitable for the output of six cows. The volume of digester is 8.3 m3 , the volume of gas holder is 2.2 m3 and the retention time is 22 days. Find the height of gas holder in centimeter.
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Two gaseous streams containing the same fluid enters a mixing chamber and leaves as a single stream. For the first gas the entrance conditions are A1=500 cm², v1=230 m/s, p1=1.60 kg/m³. For the second gas the entrance conditions are A2= 300 cm³, m2=8.84 kg/s, v2=0.502 m³/kg. The exit stream conditions is v3=130 m/s and v3=0.437 m3/kg. Determine the following: (a) the total mass flow leaving the chamber (kg/sec) (b) the velocity of the gas at 2. (m/sec)
A special case of a linear function occurs when we talk about direct variation. If the quantities x and y are related by an equation y − kx for some constant k ± 0, we say that y varies directly as x, or y is proportional to x. The constant k is called the constant of proportionality. Equivalently, we can write fsxd − kx, where f is a linear function whose graph has slope k and y-intercept 0. (a) As dry air moves upward, it expands and cools. If the ground temperature is 20°C and the temperature at a height of 1 km is 10°C, express the temperature T (in °C) as a function of the height h (in kilometers), assuming that a linear model is appropriate. (b) Draw the graph of the function in part (a). What does the slope represent?(c) What is the temperature at a height of 2.5 km?
You are developing a porous membrane for use in a dialysis system. The membrane must be able to retain both protein and glucose on the inlet side and allow other, smaller molecules to flow through. You have found that the membrane is 0.25 mm thick and contains long, rectangular pores with a width of 0.1 microns. 57% of the 50 cm^2 membrane surface area is covered with pores. A test fluid (viscosity = 1.5 cP, density = 1015 kg/m^3) is passed through the membrane. You can assume that the test fluid has a composition similar to that of blood plasma. An initial test is run at physiological conditions, and you observe that the flow rate of fluid through the membrane is 500 cm^3/min. Given this data, what must the hydrodynamic pressure drop across the membrane in your test system be in pascals?
Completely solve and box the final answers. Write legibly 9. A blower with the inlet open to the atmosphere delivers 250 cubic meters per minute of air at a pressure of 2.50 cm of water gage through a duct 25 cm in diameter, the manometer being attached to the discharge duct at the blower. Air temperature is 25 degrees C and the barometer pressure reads 1.025 bar. Calculate the required motor rating in KW if the blower efficiency is 92.5%
THERMODYNAMICS (ALREADY ANSWERED IN BARTLEBY. PLEASE CHECK IF THEIR ANSWER IS CORRECT) UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
the following data is obtained for the velocity of a vehicle during a crash test: t(ms) v(mph) 0 30 10 29.5 20 28 30 23 40 10 50 5 60 2 70 0.5 80 0 if the vehicle's weight is 2,400 lb, approximate the force f in lb acting on the vehicle 40ms after the crash. the force can be calculated by F=m(dv/dt) , and the mass of the car m is 2400/32.2 slug. note that 1 ms=10^-3 s and 1 mile = 5,280 ft. convert t to secons and mph to fps. use 1st order forward, backward, and centered difference and apply Richardson's approximation. use h1=0.02 and h2-0.01s.Show detailed solution. Thanks!