You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A, B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC=0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa. b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, c to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tạc

You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A, B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC=0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa. b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, c to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tạc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 35cm respectively. If driven shaft runs with 8 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 5mm
The upper half of a compound Epicyclic gearset is shown in Figure, with input shaft I rotating at a constant speed of 700 rpm in a clockwise direction and generating 12 kW input power. The Annulus wheel A2 is coupled to an auxiliary gear N on shaft X and forms a compound wheel with gear O. The Annulus A1 rotates in a counter-clockwise direction at a speed of 5,300 rpm. Calculate the following using this condition: Number of gear teeth:P1 = 30 , A1 = 120P2 = 50 , A2 = 140N = 60 , O = 120 a) The output shaft O (NO), shaft X (NX), and gear ratio speed and direction (n). b) Calculate the speed and direction of output shaft O (NO), shaft X (NX), and gear ratio if Annulus wheel A1 is locked (n). c) The braking torque (Tb) that must be applied to Annulus wheel A1 to keep it stationary (magnitude and direction), assuming gear transmission efficiency of 90%.
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
What is the minimum diameter in meter of a solid steel shaft that will not twist through more than 3˚ in 6 meter length, when subjected to a torque of 14 kN m. Use G of 83 Gpa.
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
What is the minimum diameter of a solid steel shaft that will not twist through more than 4o in a 9 m length when subjected to a torque of 11 kN.m ? if G = 83 GPa
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 290 kW(ii) speed = 60 rpm,(iii) Maximum shear stress = 65 MPa(iv) diameter ratio = 1.5(v) The maximum value of the twisting moment is 40% greater than its mean. The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
PLEASE ANSWER ?? ?Part 1 Calculate the polar moments of inertia in segments (1) and (2). Please Answer: J₁ = in.⁴ J₂= in. ⁴ ?Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Please Answer: T₁ = Ib-ft, T₂= Ib-ft. ?Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Please Answer: τ₁ = psi, τ₂ = psi ?Part 4 Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. ?Part 5 Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad. Thank you so much in advance
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° (degrees) in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m^2. Convert your answers to mm.
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B