You have been selected as a potential intern in a construction company in Aqaba, Jordan. For evaluation purposes, you were asked to answer the following question. Two wooden boxes are moving on an inclined surface as shown in Figure 2. Wooden Воx A Non- Frictional Surface Non- Frictional Surface 60 Figure 2: Wooden Boxes Answer the following questions using the D'Alembert's principle. Note that the mass of box A is M1 and the mass of box B is M2. 1. Find the tension in the rope, in terms of M1 and M2. 2. Calculate the acceleration of the wooden boxes, in terms of M1 and M2. Wooden Вох

You have been selected as a potential intern in a construction company in Aqaba, Jordan. For evaluation purposes, you were asked to answer the following question. Two wooden boxes are moving on an inclined surface as shown in Figure 2. Wooden Воx A Non- Frictional Surface Non- Frictional Surface 60 Figure 2: Wooden Boxes Answer the following questions using the D'Alembert's principle. Note that the mass of box A is M1 and the mass of box B is M2. 1. Find the tension in the rope, in terms of M1 and M2. 2. Calculate the acceleration of the wooden boxes, in terms of M1 and M2. Wooden Вох

Name: You have been selected as a potential intern in a construction compan
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: You have been selected as a potential intern in a construction company in Aqaba, Jordan. For evaluationpurposes, you were asked to answer the following question. Two wooden boxes are moving on an inclinedsurface as shown in Figure 2.WoodenВоxANon- F

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.37P

See similar textbooks

Similar questions

The parametric equations of the plane curve known as a cycloid are x=a(sin) and y=a(1cos). Use integration to find the coordinates of the centroid of the cycloid obtained by varying from 0 to 2 rad.
This problem is related to DYNAMICS OF RIGID BODIES, help me find each answer and write it on clean paper complete the solution, and box the final answer. Thank you
The following questions consider the stability of a floating iceberg. Approximate the iceberg as a perfect cylinder of uniform density, If the iceberg has a diameter of 3 meters and a length of 0.5 meters find the location of the metacenter as measured from the bottom of the iceberg. Take the density of sea water to be 1030 kg/m3 and the density of the ice to be 920 kg/m3.
An artificial pond was constructed in the local park last year by digging a hole in the shape of a perfect hemisphere of radius 2 m, and then filling it with water. Now, a year later, the pond needs cleaning, and the city workers need to pump out all of the water. In order to do so, energy must be expended to lift the water (working against gravity) from down inside the pond up to ground level. It is known that the energy, E required to lift a mass m (in kg) to a height h (in m) is given by E = mgh (where g can be taken to be 10 m/s2). You can take the density of water to be 1000 kg/m3. How much energy is required in total to pump all of the water out the pond?
Two spheres, one heavier and weighing12000 N and of diameter 1.2 m and the other lighter and weighing 4000 N, are tied with a rope and placed in seawater. The density of sea water is 1025 kg/m^3. It was found that the spheres floated vertically with the lighter sphere just under the water surface. Illustrate the problem before answering the following questions: (a) Determine the diameter of the lighter sphere in meters. (b) Determine the tension in the rope in Newtons. Please answer this with diagram PLEASE. ASAP po.
A loaded scow has draft of 1.6 m in sea water (sg = 1.03) when in upright position. The scow is 6 m wide and 12 m long and 2.4 m high. The center of gravity of the scow is 1.8 m above the bottom along the vertical axis of symmetry. Assume that the center of buoyancy is located half of the height of draft. What is the maximum single weight in kN that can be moved transversely from the center of the unloaded scow over the top edge without sinking the scow? (Considering rolling position)
The iceberg idealization may becomeunstable if its sides melt and its height exceeds its width. InFig. suppose that the height is L and the depth intothe paper is L , but the width in the plane of the paper isH , L. Assuming S =0.88 for the iceberg, fi nd the ratio H / Lfor which it becomes neutrally stable (about to overturn).
A uniform horizontal pipe weighing 10 kg and 1.5 m long is used as a lever. If you need to balance two objects (one on each end), where should the fulcrum be placed? The objects weigh 25 kg and 52 kg. What is the reaction force exerted by the support on the pipe? Draw the complete diagram to describe your final answer (include the lengths).
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is given as γ=8°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=50°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N)b) Find the tensile force T2 in cable 2. (Write your result in N)c) Find the angle α of cable 1 with the horizontal.
Please state the formulas used and write the answer clearly and completely. Includealsothe free body diagram.Thank you!
Complete solution with free body diagram.