You have five different resistors, each with a unique resistance constant. Which of the following schemes should you use to connect the resistors in such a way to produce the largest equivalent resistance possible? Simply use the single resistor with the highest resistance O Simply use the single resistor with the lowest resistance Connect all five in series Connect all five in parallel Use a combination of the two with the highest resistances in series, then connected to the resistor with the lowest resistance value in parallel Use a combination of the two with the highest resistances in parallel, then connected to the resistor with the lowest resistance value in series O Cannot be determined without knowing the individual resistances

You have five different resistors, each with a unique resistance constant. Which of the following schemes should you use to connect the resistors in such a way to produce the largest equivalent resistance possible? Simply use the single resistor with the highest resistance O Simply use the single resistor with the lowest resistance Connect all five in series Connect all five in parallel Use a combination of the two with the highest resistances in series, then connected to the resistor with the lowest resistance value in parallel Use a combination of the two with the highest resistances in parallel, then connected to the resistor with the lowest resistance value in series O Cannot be determined without knowing the individual resistances

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter28: Direct-current Circuits

Section: Chapter Questions

Problem 28.3OQ: The terminals of a battery are connected across two resistors in series. The resistances of the...

See similar textbooks

Similar questions

Show that the power dissipated by the load resistor is maximum when the resistance of the load resistor is equal to the internal resistance of the battery.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
A 2.00- and a 7.50F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor.Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
When resistors with different resistances are connected in series, which of the following must be the same for each resistor? Choose all correct answers. (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
In the circuit shown in Figure OQ21.15, each battery is delivering energy to the circuit by electrical transmission. All the resistors have equal resistance. (i) Rank the electric potentials at points a, b, c, d, and e from highest to lowest, noting any cases of equality in the ranking. (ii) Rank the magnitudes of the currents at the same points from greatest to least, noting any cases of equality.
A battery with an internal resistance of 10.0 produces an open circuit voltage of 12.0 V. A variable load resistance with a range from 0 to 30.0 is connected across the battery. (Note: A battery has a resistance that depends on the condition of its chemicals and that increases as the battery ages. This internal resistance can be represented in a simple circuit diagram as a resistor in series with the battery.) (a) Graph the power dissipated in the load resistor as a function of the load resistance. (b) With your graph, demonstrate the following important theorem: The power delivered to a load is a maximum if the load resistance equals the internal resistance of the source.
The timing device in an automobile's intermittent wiper system is based on an RC rime constant and utilizes a 0.500F capacitor and a variable resistor. Over whatrange must R be made to vary to achieve time constants from 2.00 to 15.0 s?
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
Construe! Your Own Problem Consider a rechargeable lithium cell that is to be used to power a camcorder. Construct a problem in which you calculate the internal resistance of the cell during normal operation. Also, calculate the minimum voltage output of a battery charger to be used to recharge your lithium cell. Among the things to be considered are the emf and useful terminal voltage of a lithium cell and the current it should be able to supply to a camcorder.
A rechargeable battery has an emf of 13.2 V and an internal resistance of 0.850 . It is charged by a 14.7-V power supply for a time interval of 1.80 h. Alter charging, the battery returns to its original state as it delivers a constant current to a load resistor over 7.30 h. Find the efficiency of the battery as an energy storage device. (The efficiency here is defined as the energy delivered to the load during discharge divided by the energy delivered by the 14.7-V power supply during the charging process.)
Resistors are commonly rated at 18W,14W,12W ,1 W and 2 W for use in electrical circuits. If a current of1 = 2.00 A is accidentally passed through a R=1.00 resistor rated at 1 W, what would be the most probable outcome? Is there anything that can be done to prevent such an accident?