You have given the above diagram of a resistor network. The numerical values of the resistors are R2=4kΩ, R3=8kΩ, R4=8kΩ, R5=12kΩ, R6=2kΩ, R7=4kΩ. And the e.m.f s are V1=10.0volts, V2=10.0volts, V3=14.0volts, a) Find the equivalent resistance across the terminal cd. equivalent resistance b) Draw the diagram in your script and then apply KVL and KCL to it. Write down the equations accordingly. c) Find the value of the current passing through resistor R3.

You have given the above diagram of a resistor network. The numerical values of the resistors are R2=4kΩ, R3=8kΩ, R4=8kΩ, R5=12kΩ, R6=2kΩ, R7=4kΩ. And the e.m.f s are V1=10.0volts, V2=10.0volts, V3=14.0volts, a) Find the equivalent resistance across the terminal cd. equivalent resistance b) Draw the diagram in your script and then apply KVL and KCL to it. Write down the equations accordingly. c) Find the value of the current passing through resistor R3.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

(a) During surgery, a current as small as 20.0A applied directly to the heart may cause ventricular fibrillation. If the resistance of the exposed heart is 300 what is the smallest voltage that poses thisdanger? (b) Does your answer imply that special electrical safetyprecautions are needed?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
An ECG monitor must have an KC time constant lessthan 1.00102s to be able to measure variations involtage oversmall time intervals, (a) If the resistance of the circuit (duemostly to that of the patient's chest) is 1.00kTwhat is the maximum capacitance of the circuit?(b) Would It be difficult in practice to limit the capacitance to less than the value found in (a)?
The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (Fig. P21.71). The unknown resistance Rx is between points C and E. Point E is a true ground, but it is inaccessible for direct measurement because this stratum is several meters below the Earths surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure is as follows. Measure resistance R1 between points A and B, then connect A and B with a heavy conducting wire and measure resistance R2 between points A and C. (a) Derive an equation for Rx in terms of the observable resistances, R1 and R2. (b) A satisfactory ground resistance would be Rx 2.00 . Is the grounding of the station adequate if measurements give R1 = 13.0 and R2 = 6.00 ? Explain. Figure P21.71
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
You have given the above diagram of a resistor network. The numerical values of the resistors are R1=4kΩ, R2=12kΩ, R4=8kΩ, R5=2kΩ, R6=4kΩ, R7=12kΩ. And the e.m.f s are V1=10.0volts, V2=13.0volts, V3=12.0volts, a) Find the equivalent resistance across the terminal TS. b) Draw the diagram by hand and then apply KVL and KCL to it. Write down the equations accordingly. c)
You have given the above diagram of a resistor network. The numerical values of the resistors are R1=8kΩ , R2=8kΩ , R3=6kΩ , R4=6kΩ , R5=4kΩ , R6=12kΩ , R7=4kΩ . And the e.m.f s are V1=10.0volts , V2=10.0volts , V3=10.0volts. a) Find the value of the current passing through resistor R2 b) Calculate the potential difference across R6
In the figure the ideal batteries have emfs ε1 = 18.2 V, ε2 = 9.68 V, and ε3 = 4.90 V, and the resistances are each 2.00 Ω. What is the (a) size of current i1? (d) what is battery 1's power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power?
In the circuit of, E = 100 V, C = 5 μF, R1 = R2 = R3 = 0.2 MΩ. With C completely uncharged, switch S is suddenly closed (at t = 0).(a) At t = 0, what is current in R1 resistors?(b) After a very long time, what are currents in R2 resistors?
In the circuit of, E = 100 V, C = 5 μF, R1 = R2 = R3 = 0.2 MΩ.With C completely uncharged, switch S is suddenly closed (at t = 0).(a) At t = 0, what is current in R1 resistors?(b) After a very long time, what are currents in R2 resistors?
In the figure R1 = 5.11 Ω, R2 = 15.3 Ω, and the ideal battery has emf ε = 12.4 V. (a) What is the magnitude of current i1? (b) How much energy is dissipated by all four resistors in 0.518 min?
(a) At what temperature would the resistance of a copper conductor be double its resistance at 20.0 C? (Use 20.0 C as the reference point in Eq. 26-17; compare your answer with (b) Does this same “doubling temperature” hold for all copper conductors, regardless of shape or size?