You measured the potential difference along the Al (Aluminum) wire while uniform current was flowing through the wire. The radius of the wire is 2.40mm and the length is 4m. The measured potential was plot as V(x) vs. x as below. Calculate the current flowing in the Aluminum wire? Resistivity of Al is 2.82x 10-82 m)

You measured the potential difference along the Al (Aluminum) wire while uniform current was flowing through the wire. The radius of the wire is 2.40mm and the length is 4m. The measured potential was plot as V(x) vs. x as below. Calculate the current flowing in the Aluminum wire? Resistivity of Al is 2.82x 10-82 m)

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 63P: Consider a power plant is located 60 km away from a residential area uses Q-gauge (A=42.40mm2) wire...

See similar textbooks

Similar questions

An electronic device designed to operate at any temperature in the range from 10.0C to 55.0C contains pure carbon resistors. By what factor does their resistance increase over this range?
A 10-gauge copper wire has a cross-sectional area A=5.26mm2 and carries a current of I=5.00A . The adensity of copper is =89.50g/cm2 . One mole ofcopper atoms (6.021023atoms) has a mass ofapproximately 63.50 g. What is the magnitude of the drift velocity of the elections, assuming that each copper atom contributes one free electron to the current?
Consider a power plant is located 60 km away from a residential area uses Q-gauge (A=42.40mm2) wire ofcopper to transmit power at a current of I = 100.00 A.How much more power is dissipated in the copper wires than it would be in superconducting wires?
Consider a resistor of resistivity 4.12 × 10-8 Ω • m. If an electric field of 19 V/m is applied across the resistor and the electron volume concetration in the conductor is 5.82 × 1028 per m3, determine the drift velocity, in mm/s, of the free electron constituting the current.
Consider a conductor of length 69 millimeters and inner and outer diameters 7.98 millimeters and 13.77 millimeters, respectively. The charge carriers, as a group, travels end to end of the conductor in 4.68 seconds. If the electron volume concentration of the conductor is 7.00 × 1025 electrons per cubic meter, find the total current, in amperes, through the conductor.
A 22-gauge copper wire has a radius of 0.645 mm, is 5.00 m long, and has a resistivity r = 1.72 ´ 10-8 ohm-m. The maximum current for which this wire is rated is 0.920A. What is the maximum electric potential difference that may be applied to this wire without overloading it ?
Consider a resistor of resistivity 1.59x10^-8 ohms•m. If an electric field of 19 V/m is applied across the resistor and the electron volume concentration in the conductor is 4.7x10^28 per cubic meter, determine the drift velocity, in mm/s, of the free electron constituting the current.
A metal object having a length (10m), cross section area (0.5 mm2), and resistance (0.52) is connected to a potential difference source of 5V at room temperature. If the density of free electrons equals (8×1025 electron/m³), Calculate the thermal velocity.
A wire 3.77 m long and 6.81 mm in diameter has a resistance of 20.6 mΩ. A potential difference of 26.6 V is applied between the ends. What is the magnitude of the current density? Current in the wire is 1291.26 A Answer isnt 11284400, 3547400000,
A wire of diameter 0.800 mm and length 25.0 m has a measuredresistance of 1.60 Ω. What is the resistivity of the wire?
What current flows through a 2.74 cm diameter rod of pure silicon that is 25.0 cm long, when 1000 V is applied to it? (Such a rod may be used to make nuclear particle detectors, for example.) The resistivity of pure silicon is 2.30 103 Ω · m. _____A
An unknown wire in a circuit has a circular cross-section with diameter 3.8 mm. It carries a current of 4.2 mA. If you assume the drift velocity in this wire is 1 × 10-2 cm/s, what is the density of charge carriers per cubic centimeter? If the conductivity in this wire is 3.5 × 106 Ω-1 m-1, what is the average time between collisions, in nanoseconds? J=37.03 n=???? τ =????