You pull downward with a force of 28 N on arope that passes over a disk-shaped pulley of mass 1.2 kg and radius0.075 m. The other end of the rope is attached to a 0.67-kg mass.(a) Is the tension in the rope the same on both sides of the pulley?If not, which side has the greater tension? (b) Find the tension inthe rope on both sides of the pulley

You pull downward with a force of 28 N on arope that passes over a disk-shaped pulley of mass 1.2 kg and radius0.075 m. The other end of the rope is attached to a 0.67-kg mass.(a) Is the tension in the rope the same on both sides of the pulley?If not, which side has the greater tension? (b) Find the tension inthe rope on both sides of the pulley

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section8.2: Rotational Dynamics

Problem 27PP

See similar textbooks

Similar questions

A grindstone with a mass of 50 kg and radius 0.8 m maintains a constant rotation rate of 4.0 rev/s by a motor while a knife is pressed against the edge with a force of 5.0 N. The coefficient of kinetic friction between the grindstone and the blade is 0.8. What is the power provided by the motor to keep the grindstone at the constant rotation rate?
An object of mass M = 13.0 kg is attached to a cord that is wrapped around a wheel of radius r = 10.5 cm (see figure). The acceleration of the object down the frictionless incline is measured to be a = 2.00 m/s2 and the incline makes an angle ? = 37.0° with the horizontal. Assume the axle of the wheel to be frictionless.
A 0.31-kg cart on a horizontal air track is attached to a string. The string passes over a disk-shaped pulley of mass 0.080 kgand radius 0.012 m and is pulled vertically downward with a constant force of 1.1 N. Find (a) the tension in the stringbetween the pulley and the cart and (b) the acceleration of the cart.
A 65 kg student is in a car traveling at 25 m/s on a hill of radius 110 m. When the car is at the top of the hill, what upward force does the seat exert on the student? A 4.2 m long uniform post is supported by a cable having a tension of 1 700 N. What is the mass of this post?
If the required clamping force at the board A is to be 2.50 kN, determinethe torque M that must be applied to the screw to tighten it down. Thesquare-threaded screw has a mean radius of 10.0 mm and a lead of 2.50 mm, and the coefficient of static friction is μS = 0.500
The horizontal force F (affecting the axis) required to drive a wheel weighing W and a radius R over a block height of h is: *(Choose and the solution method must be attached)
A person is pushing a wheelbarrow along a ramp that makes an angle ?=43.0∘ with the horizontal. The wheelbarrow and load have a combined mass of ?=24.05 kg with the center of mass at the midpoint of the length ?. What is the magnitude of the net force ?net that the person must apply in order to push the wheelbarrow up the ramp at a constant velocity, while keeping the wheelbarrow in a level, horizontal orientation? Assume that the radius of the wheel is small enough to ignore. Use ?=9.81 m/s2.
The arm of a crane at a construction site is17.0 m long, and it makes an angle of 16.8◦with the horizontal. Assume that the maximum load the crane can handle is limitedby the amount of torque the load producesaround the base of the arm.What maximum torque can the crane withstand if the maximum load the crane canhandle is 785 N?Answer in units of N · m.
You pull downward with a force of 30 N on a rope that passes over a disk-shaped pulley of mass 1.5 kg and radius 0.075 m. The other end of the rope is attached to a 0.67 kg mass. Find the tension in the rope on both sides of the pulley.
To loosen the lid on a jar of jam 7.6 cm in diameter, a torque of11 N # m must be applied to the circumference of the lid. If a jarwrench whose handle extends 15 cm from the center of the jar isattached to the lid, what is the minimum force required to openthe jar?
A man applies a torque to a nut with a wrench 0.450 m long. Because of the cramped space, he must exert a force upward at an angle of 68.0° with respect to a line from the nut through the end of the wrench. If the force he exerts has magnitude 52.0 N, what magnitude torque (in N · m) does he apply to the nut? (Assume that the force is applied at the end of the wrench.)
A bicycle wheel is 64.6 cm in diameter and weighs 1.87 kg. Assume the wheel is a hoop, with all of the mass focused on the radius on the outside. The bicycle is put on a stationary stand, and a tangent force of 125 N is given to the tire's rim. (a) What force must be supplied by a chain traveling over a sprocket with a diameter of 8.96 cm in order for the wheel to accelerate at 4.49 rad/s 2? (b) What force is necessary if the chain is shifted to a sprocket with a diameter of 5.57 cm?