Solve Problem 14.9 using the Danish formula [Eq. (14.52)]. Use FS = 3. Problem 14.9 A steel pile (H-section; HP 330 x 1.462; see Table 14.1) is driven by a hammer. The maximum rated hammer energy is 50 kN-m, the weight of the ram is 58 kN, and the length of the pile is 25 m. Also given are the following:

Solve Problem 14.9 using the Danish formula [Eq. (14.52)]. Use FS = 3. Problem 14.9 A steel pile (H-section; HP 330 x 1.462; see Table 14.1) is driven by a hammer. The maximum rated hammer energy is 50 kN-m, the weight of the ram is 58 kN, and the length of the pile is 25 m. Also given are the following:

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.21P: Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly...

See similar textbooks

Similar questions

A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Refer to Figure 18.23. Given L1=3m, L2=6m, l1=1.5m, =16.5kN/m3, sat=19.0kN/m3 and =35. a. Find the required depth of the sheet pile, increasing the theoretical estimate by 30%. b. Determine the force in the tie rods if they are spaced 3 m apart horizontally. c. Find the maximum bending moment in the sheet pile.
The section of a 4 x 4 group pile in a layered saturated clay is shown in Figure P 9.29. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing (d) of the piles is 1 m. Determine the allowable load bearing capacity of the pile group. Use FS = 3 and Table 9.10.
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36
Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of 3. Use K = 1.5 Ko and = 0.65 in computing the shaft load. Use Meyerhofs method for computing the point load.
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.
Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m3 and = 33. Assuming = 0.7 and K = 1.4 Ko, determine the load-carrying capacity of the pile with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
A 400-mm diameter and 15 m long concrete pile is driven into a sand where = 18.0 kN/m3 and = 31. Assuming = 0.65 and K = 1.4 Ko, determine the load carrying capacity of the pile with a factor of safety of 3.