Identify which gear was the largest—the driving or the driven gear.

Q: A 50 mm hollow wooden cube has a mass of 20 kg floats vertically in the water with a specific weight...

A: Given: The diameter of the wooden cube, d = 50 mm The mass of the wooden cube, m = 20 kg The specifi...

Q: Explain the difference between Flat Rolling and Shape Rolling processes.                        ple...

A: Flat rolling: In flat rolling operation, the material is rolled between normal rolls. The desired sh...

Q: (g) If the pressure at point B(3 m,2 m) is 600 kPa, determine the pressure at point C(1 m,3 m). Take...

A: Given Data: The coordinate of point B is (3,2). The coordinate of point C is (1,3). The pressure at...

Q: Consider a combined gas–steam power plant that has a net power output of 45 MW. The pressure ratio o...

A: The T-s diagram of the above combined gas-steam power plant is

Q: 2/7 The two structural members, one of which is in ten- sion and the other in compression, exert the...

A:

Q: A stainless steel pipe has a thermal conductivity of k = 15 W/[m degrees Celsius]), with a 3cm inner...

A: Draw the schematic diagram for the given problem.  

Q: A car travels along a straight east-west road. A coordinate system is established on the road, with ...

A: Given Data⇒displacement x=12 miletime, t=45 minutesProblem definition⇒Problem says determine the ave...

Q: A wooden log of 0.8m diameter and 6m length is floating in water. Find the depth of wooden log in wa...

A: Given dataDiameter of the log D = 0.8mLength of the log floting in water L=6mSpecific gravity of woo...

Q: How does fuel cost and efficiency affect both air carrier costs and pricing?

A: The reaction of air carriers to higher fuel costs is to improve efficiency. 

Q: (a) Calculate reactions at A and B in beam shown in Figure Q17

A: Given data: Point load = P = 1000 N Length AB = 9 m Moment = M = 2100 N-m.

Q: 9. Determine force P for impending motion to the left if the coefficient of friction for all surface...

A: In the given problem, the impending motion is to the left, thus friction force acting on the block A...

Q: 1. An engine operates on the air-standard Otto Cycle. The net cycle work of air is 1000 kJ/kg with m...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: 1- -- pom-) A pilot of mass m= 70 kg in a jet aircraft executes a loop-the-loop, as shown in Figure....

A: mass=70Kg radius=3Km v=250m/s Ans(a) Centripetal acceleration ac=v2r=25023000=20.833 m/s2  

Q: According to the following figure, calculate the horizontal and vertical force on a circular segment...

A: Given: The radius of the segment, r = 2 m The width of segment, b = 5 m

Q: Q#4:(a) Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.

A: Corner radii are important in sheet metal drawing process because the radii of punch and die avoid t...

Q: The closed piston cylinder system contains N2 gas at 5 bar and 127°C with initialvolume of 750 cm3. ...

A:

Q: The cross-section of a rectangular beam 25 mm by 72 mm and is subjected to a combined loading of 65 ...

A:

Q: Consider the flow field shown. Coordinates are measured in meters. For the particle that passes thro...

A: Given: Velocity of the flow field is,  V=axti+bj where, a=1/4 s-2 and b=1/3 m/s Point at time t =0, ...

Q: In the followign figure, axis y-y is fixed while axes x-x and z-z move with the arm. Gear 7 is fixed...

A:

Q: An inventor claims to have invented a heat engine that has thermal efficiency of 85% when operating ...

A:

Q: The magnitude of A is 50 kN and B is 40 kN. If the resultant is directed along the positive x axis, ...

A: Given The magnitude of force is A=50 kN inclined at angle of θ with vertical. The magnitude of forc...

Q: Explain on the differences between the energy transferred to the fluid and from the fluid in the ene...

A: The energy equation represents the net energy content of the fluid at given conditions. The fluid ca...

Q: Is strain is a measurable quantity? If yes, then explain how will you measure it.

A: The strain is described as a quantity that takes place due to the application of the load. When a lo...

Q: Q.1 a) Derive a relation for Joule – Thomson coefficient for a gas whose equation of state is (P+) =...

A: (a) Write the given equation. P+aV2V=RT From the above expression we get: P+aV2V=RTT=1RPV+av......1 ...

Q: Translate : The x, y fluids with dx and dy densities that do not mix with each other are in equilibr...

A: Given Data: The density of the blue fluid is dx. The density of the yellow fluid is dy. The gauge ...

Q: Draw Isometric view

A: Isometric projection Isometric projection is a method for representing three-dimensional objects int...

Q: Please give answers to both of these parts, thanks (a) Manufacturing is “ the transformation of mate...

A: Manufacturing can be defined as the bulk production of any useful item from the raw materials using ...

Q: Determine the normal force P that must be exerted on the rack to begin pushing the 100kg pipe shown ...

A: The rack Must exert a force p on the pipe due to force equilibrium in the x-direction. If slipping b...

Q: Q 04: The 80-kg crate shown in Fig. rests on a horizontal surface for which the coefficient of kinet...

A: Given Data: The mass of the crate is m = 80 kg. The force acting on the crate is F = 400 N. The ang...

Q: 5. The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the...

A:

Q: A rod 25 mm in diameter is held between fixed bearings 1.2 m apart and deflects under its static wei...

A: Given: d=25 mmL=1.2 m = 1200 mmρ=7900 kg/m3N=750 rpmE=205 GPa

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.