BuyFind*arrow_forward*

6th Edition

KASSIMALI + 1 other

Publisher: Cengage,

ISBN: 9781337630931

Chapter 5, Problem 60P

Textbook Problem

399 views

Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the frame shown.

To determine

Plot the shear diagram, bending moment diagram, axial force diagram, and the qualitative deflected shape of the frame.

Write the condition for static instability, determinacy and indeterminacy of plane frames as follows:

Here, number of members is *m*, number of external reactions is *r*, the number of joints is *j*, and the number of elastic hinges is

Find the degree of static indeterminacy (*i*) using the equation;

Refer to the Figure in the question;

The number of members (*m*) is 2.

The number of external reactions (*r*) is 3.

The number of joints (*j*) is 3.

The number of elastic hinges

Substitute the values in Equation (2);

Show the free-body diagram of the entire frame as in Figure 1.

Find the resultant reaction at point *A* by taking moment about point *C*.

Show the free-body diagram of the members and joints of the entire frame as in Figure 2.

Consider point *A*:

Resolve the vertical component of forces.

Consider the member *AB*:

Resolve the vertical component of forces.

Take moment about the point *B*.

Consider the point *B*:

Resolve the vertical component of forces.

Structural Analysis

Show all chapter solutions

Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...

Ch. 5 - 5.1 through 5.11 Determine the axial forces,...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - Draw the shear and bending moment diagrams for the...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...

Find more solutions based on key concepts

Show solutions Refer to Problem 2.C.1. Results of the sieve analysis for Soils A, B, and C are given below. To obtain a more r...

Principles of Geotechnical Engineering (MindTap Course List)

Explain the difference between average and instantaneous speed.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

For a soil, given: D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Calculate the uniformity coefficient and the coeff...

Fundamentals of Geotechnical Engineering (MindTap Course List)

A plate is used as a bracket and is attached to a column flange, as shown in Figure P8.2-3. Use an elastic anal...

Steel Design (Activate Learning with these NEW titles from Engineering!)

Figure 5-40 is a sketch of a clean materials recovery facility. The (low rates of the various materials streams...

Solid Waste Engineering

Why were SMEs slow to adopt ERP software? What changed to make ERP software more attractive for SMEs?

Principles of Information Systems (MindTap Course List)

Define the terms, CBT and WBT.

Enhanced Discovering Computers 2017 (Shelly Cashman Series) (MindTap Course List)

0 Describe three methods for assessing the financial attractiveness of an information system project.

Fundamentals of Information Systems

Assume that the deflected shape of a beam AB with immovable pinned supports (see figure) is given by the equati...

Mechanics of Materials (MindTap Course List)

Select the best answer for each of the following. What does IEC stand for? a. Intensity of current, EMF, and Ca...

Electric Motor Control

List and describe the different types of databases.

Database Systems: Design, Implementation, & Management

About a year ago, you purchased and installed a new router at one of your companys satellite offices, and you h...

Network+ Guide to Networks (MindTap Course List)

A 120-volt air conditioner draws 13 amperes. What size is the circuit to which the air conditioner will be conn...

EBK ELECTRICAL WIRING RESIDENTIAL

Trace the history of system architecture, with particular emphasis on the impact of the personal computer and t...

Systems Analysis and Design (Shelly Cashman Series) (MindTap Course List)

Find the name of each trip containing the word Loop.

A Guide to SQL

There are many ways to clean parts while they are being serviced. These methods can be grouped into three separ...

Automotive Technology

How does a signature-based IDPS differ from a behavior-based IDPS?

Principles of Information Security (MindTap Course List)

The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizonta...

International Edition---engineering Mechanics: Statics, 4th Edition

Write a query to count the number of invoices.

Database Systems: Design, Implementation, & Management

While discussing ignition systems: Technician A says that an ignition system must supply high-voltage surges to...

Automotive Technology: A Systems Approach (MindTap Course List)

What is an InfoSec framework?

Management Of Information Security

Research and Analysis Using the Annual Report Obtain Whole Foods' 2016 annual report (filed November 18, 2016) ...

Cornerstones of Financial Accounting

Use the data in the steam tables (Appendix A) to answer the following: A. Find the change in internal energy wh...

Fundamentals of Chemical Engineering Thermodynamics (MindTap Course List)

Identify and briefly discuss the most common examples you observe of co-workers wasting time in non-productive ...

Fundamentals of Information Systems

Label the hypotenuse, adjacent side, and opposite side of the given triangle as related to angle A.

Precision Machining Technology (MindTap Course List)

Name three methods used to perform welding, cutting, or brazing operations.

Welding: Principles and Applications (MindTap Course List)

If your motherboard supports ECC DDR3 memory, can you substitute non-ECC DDR3 memory?

A+ Guide to Hardware (Standalone Book) (MindTap Course List)