What is the difference between applications and computer-based information systems?

Q: Please, solve task 1

A: bdsfchdsgiuherugh

Q: 1.19 A square isothermal chip is of width w = 5 mm on a side and is mounted in a substrate such that...

A: The width of square isothermal chip is, w=5 mm The temperature of the coolant is, T∞=15°C The maximu...

Q: A uniform pipe cover of radius r=240 mm and mass 30 kg is held in a hor-. izontal position by the ca...

A: Given data: Radius = 240 mm                     Mass = 30 kg                     Figure with relevan...

Q: Question No. 2. The point at A the total acceleration of airplane is 3g. If airspeed is 800 km/h and...

A: Given data  total acceleration at A (a) = 3g =3*9.81 = 29.43 m/s2 airspeed (v) = 800 km/hr =800*1000...

Q: Draw free body diagram for the dynamic model of the mechanism write dynamic equilibrium equations ha...

A:

Q: If FB = 30 lb and Fc= 45 lb. Determine the resultant moment about the bolt located at A. 0.75 ft 2.5...

A: Given information: The forces: FB = 30 lb Fc = 45 lb The angle the forces make with the perpendicula...

Q: Thank you

A: Given data as per question Diameter of shaft =15 mm F =055 KN p =7 KN t = 32 N.m considering axial s...

Q: Ethylene glycol with a mass flow rate of 0.01 kg / sec flows in a thin-walled pipe with a diameter o...

A:

Q: Consider steady, incompressible, laminar flow of a Newtonian fluid in the narrow gap between two inf...

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: The 4cm thick large copper plate, initially at a uniform temperature of 25oC, is heated by passing i...

A: Write the given data with suitable variables. d=4 cm=0.04 m100 cm1 mTi=25 °CT∞=400 °Ct=5 min.=300 s6...

Q: In the figure, bodies x and y are released from rest. Find the velocity of mass y hitting the ground...

A: Draw the free body diagram of body X. Apply Newton's second law, T-W1=maT-mg=maT-m9.81 m/s2=maT-9.8...

Q: The system in the figure is released from a standstill. Using the conservation of energy, Find the v...

A: The free-body diagram of the system is shown as the velocity at the starting point will be zero and...

Q: 4. What are the frequencies of vibration of a mass m = 5 kg (i) on a spring with modulus k, = 20 nt/...

A: Given data: The mass of the object is m=5 kg The spring constant of the spring 1 is k1=20 Nm The spr...

Q: Determine the values of t corresponding to the maxima and minima of the oscillation y(t)=e^-t sin t....

A: The function of oscillation is given as, y(t)=e-tsint Differentiating both the sides of the above ex...

Q: The inner surface of a pipe with an inside diameter of 0.015 m is wet (concentration: 0.010 kmol / m...

A:  

Q: The homogeneous beam AB weighs 400 lb. For each support conditionshown in (a) through (d), draw the ...

A:

Q: what is the impact of mechanical vibration on following a. Bearing House of Lathe machine b. Hardeni...

A: Answer         c. Fatigue life of materials

Q: Performance of a compressor needs to be analyzed. Air enters the compressor of an air- standard Bray...

A: Note: According to the Bartleby guidelines only one question at a time can be answered. Please submi...

Q: As shown in the figure, a homogeneous rod of length L = 1 (m) m = 05 (kg) is fixed so that it can ro...

A: The length of the rod is, L=1 m Mass of the rod is, m=0.5 kg Spring constant of the both springs is,...

Q: A polytropic process of air from 150 psia, 300 degree F, and 1 ft^3 occurs to p2 = 20 psia in accord...

A: Given Data:

Q: The opposite beam is loaded with two forces P=19.2 KN and distributed load w=24 KN/m as shown. The r...

A: For the given beam  P = 19.2 kN w = 24 kN/m To determine  the shear force left of E

Q: 4. For a certain ideal gas R = 25.8 ft.lb /lb °R and k =1.09 (a) What are the values of c, and c,? (...

A: Given Data The Gas constant is: R=25.8 ft.lb/lb*R The constant is: k=1.09 The equations are Cp-Cv=...

Q: This is vibration engineering

A: Note:- According to the Bartleby guidelines, only three subparts are allowed to answer so please sub...

Q: A spherical interplanetary probe of 0.5-m diameter contains electronics that dissipate 150 W. If the...

A: Given data: Diameter of the probe d = 0.5 m Rate of energy dissipate Ein.=150 W Emissivity ε=0.8 Cal...

Q: pleas

A:

Q: In an air compressor the pressure at inlet and outlet are 1 bar and 5 bar respectively. The temperat...

A:

Q: A grey cast iron block of dimension 200 mm × 100 mm × 10 mm is produced by sand casting . Pattern ma...

A: Given data: The length of the block is l = 200 mm. The width of the block is b = 100 mm. The thickn...

Q: A homogenous mixture of 21 kg of dry air and 0.3 kg of water vapour is contained in a tank at 24°C a...

A: Since you have asked question with multiple parts we hence we will answer three sub parts for you if...

Q: A mass of 1 kg, when attached to a spring, stretches it 2 m and then comes to rest in the equilibriu...

A: Given: Mass of the body is 1 kg.  Initial compression of the spring is 2 m. Force is, f(t) = 8sin(4t...

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.