1.19 A square isothermal chip is of width w =front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C.5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; theCoolantChipIf the coolant is air and the corresponding convection coefficient is h = 200 W/m² · K, what is the maximum allowable chip power? If the coolant is adielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?

The width of square isothermal chip is, w=5 mm The temperature of the coolant is, T∞=15°C The…

1.19 A square isothermal chip is of width w = 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. Coolant Chip If the coolant is air and the corresponding convection coefficient is h = 200 W/m². K, what is the maximum allowable chip power? If the coolant is a dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?

1.19 A square isothermal chip is of width w = 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. Coolant Chip If the coolant is air and the corresponding convection coefficient is h = 200 W/m². K, what is the maximum allowable chip power? If the coolant is a dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.21P

See similar textbooks

Similar questions

1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
Consider the vertical heat sink (see the figure) used to cool a surface at 70 0C. The room temperature is 30 0C. The dimensions are given as (H=2 cm, L=5 cm, t=1 mm, W=15 cm). If the space between the fins is arranged so that the heat transfer rate is maximum, what is the heat transfer rate from the heat sink? Properties of air: ρ=1 kg/m3, k=0.03 W/mK, ν=1.5x10-5 m2/s, cp=1 kJ/kg0C, Pr=0.7
Convection heat transfer from a plate (2 m x 2 m) is 450 W. If surface temperature of plate is 450 K and surrounding temperature is 300 K, what will be value of heat transfer coefficient?
A cylindrical storage tank with diameter of 4m and a length of 10 m will hold a fluid whose temperature must be maintained at 347k. in order to size the heater required for the tank the following worst-case scenario is considered: Ambient temperature=-20 wind speed=20m/s tank wall temperature=347k what size (kW) heater will be needed?
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?
A modern cabin has a concrete floor that is 4.50 inches thick. Aroaring fire keeps the interior of the cabin at 21.0 0C while the airtemperature below the cabin is a chilly 2.00 0C. How much heat(J) is lost through the concrete floor in 4 hrs if the cabin measures4.50 m by 6.50m to 3 sig fig?