Step-by-Step Guide on How to Browse the Internet Free with Any Decoder Satellite Internet Connection with a Decoder

A network interface card is already present in the computers. The purpose of the network card is to enable the computers to connect together using a protocol in order to transfer packets of data. In order to connect the computers, a form of connection is required that links the computers. In this case the form of connection used will be ethernet (Science - Opposing Views, 2014).

Gigabit ethernet connections for both the WAN and LAN ensure the fastest file transfer speeds available. This prevents any bottlenecks between the router and modem to take full advantage of your high speed internet connection. Additionally, file sharing between up to 4 ethernet connected home computers will be lightning fast.

1. Thanks to Wi-Fi technology, this devices can connect wirelessly and seamlessly to one’s existing broadband connection in seconds.

Uses a modem which can provide both wired and wireless connections for a number of devices

Every Computer that connects to a network must have a Network Interface Card (NIC). Most new Computers have them built into the motherboard. It has one or sometimes more RJ45 socket(s) that connect to a modem. The older and deprecated version used to have RJ11 sockets to connect to the network. Due to it being extremely vulnerable to phreaking and war-dialing, it has now been replaced with

Router is a device for networking that sends packets of data between the networks of a computer. The packet of data is forwarded to routers of the networks that contain the internetwork until the packet is at the destination node. A router can be linked to several data lines from various systems. The router reads the address information in the packet to establish the ultimate destination when the data packet is in any data lines (Liu, 2012).

When setting up a LAN the architecture that you decide to choose is important. There are several factors that are decided when choosing said architecture, some of these being network speeds, types of cables, and access control mechanisms like collision detection (Team, 2011). The most common on in today’s LANs is Ethernet. These can be either wireless, wired, or a hybrid of both.

Crossover cable - A crossover cable is a type of twisted pair copper wire cable for LANs (local area network) in which the wires on the cable are crossed over so that the receive signal pins on the RJ-45 connector on one end are connected to the transmit signal pins on the RJ-45 connector on the other end.

Non Conductive: A serious concern with outdoor cables in certain computer networks is they can be hit by lightning, causing destruction to wires and other cables that are involved in the network. Fiber optic cables can be made non-conductive by avoiding metal in their design. These kinds of cables are economical and standard for many indoor applications. Outdoor versions are more expensive since they require the special strength members, but they can still be valuable in eliminating ground loop and protecting electromagnetic equipment from surge damage.

A router is a device that is used to connect dissimilar device. It is present and operates at the Network layer of the OSI model.

When first thinking of fixed line networks they think of the coaxial cable (coax) which connects to their television and twisted pair terminated with a RG-11 plug for their phones and faxes. There two variation of coax that are used in networking, thicknet (RG8) and thinnet

The 802.3 family of standards has the format 802.3x where x is a sequence of letters specifying the new standards added to the 802.3 base standard. One of the enhancements to Ethernet is Power over Ethernet (PoE), in which Ethernet cable can provide power to remote, low-power devices that are not near an electrical outlet.

This created physical connection between PC’s and the network line. Connected data’s are transporting data’s through the network. Cable is a medium through which information usually moves to one network to another network.

1. For what purpose is a transceiver used? A transceiver can be used for converting one type of Ethernet connector to another or by converting one type of I/O port to an Ethernet port. 2. This lab connects routers directly to each other via serial cables. Is this a typical configuration? No, By default, Cisco routers are DTE (Data Terminal Equipment)/ DCE (Data Circuit-Terminating Equipment) If not, to what equipment does the DCE end of the serial cable usually connect? If Router A is connected to the DTE end of the cable, Router B must be connected to the DCE end 3. What does a rollover (console) cable look like? Rollover cable is often used to connect a computer terminal to a

Ethernet Cables- Ethernet Cables will be utilized to connect all the network devices in the DesignIT LAN network. They will connect routers, switches, computers, and printers in the LAN network. I will utilize CAT5 Ethernet Cables for this network. The Ethernet cables will cost about $100 for DesignIT LAN network.