. A 6-m-long 2-kW electrical resistance wire is made of 0.2-cm-diameter stainless steel (k = 15.1 W/m °C). The re- sistance wire operates in an environment at 30°C with a heat transfer coefficient of 140 W/m². °C at the outer surface. De- termine the surface temperature of the wire (a) by using the ap- plicable relation and (b) by setting up the proper differential equation and solving it. Answers: (a) 409°C, (b) 409°C

. A 6-m-long 2-kW electrical resistance wire is made of 0.2-cm-diameter stainless steel (k = 15.1 W/m °C). The re- sistance wire operates in an environment at 30°C with a heat transfer coefficient of 140 W/m². °C at the outer surface. De- termine the surface temperature of the wire (a) by using the ap- plicable relation and (b) by setting up the proper differential equation and solving it. Answers: (a) 409°C, (b) 409°C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.60P: 1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a...

See similar textbooks

Similar questions

1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
A 0.3-cm-thick, 12-cm-high, and 18-cm-long circuit board houses 80 closely spaced logic chips on one side,each dissipating 0.06 W. The board is impregnated with copper fillings and has an effective thermalconductivity of 16 W/m · °C. All the heat generated in the chips is conducted across the circuit board andis dissipated from the back side of the board to the ambient air at 30°C, which is forced to flow over thesurface by a fan at a free-stream velocity of 400 m/min. Determine the temperatures on the two sides ofthe circuit board.
A 2.5-cm-thick sheet of plastic initially at 20oC is placed between two heated steel plates that are maintained at 140oC. The plastic is to be heated just long enough for its mid-plane temperature to reach 130oC. If the thermal conductivity of the plastic is 1.2 x 10 -3 W/m/K, the thermal diffusivity is 2.7 x 10 -6 m2/s, and the thermal resistance at the interface between the plates and the plastic is negligible, determine a) the required heating time, b) the temperature at a plane 0.6 cm from the steel plate at the moment the heating is discontinued, and c) the time required of the plastic to reach the temperature of 130oC at 0.6 cm from the steel plate.
Consider a cold aluminum canned drink that is initially at a uniform temperature of 4°C. The can is 12.5 cm high and has a diameter of 6 cm. If the combined convection/radiation heat transfer coefficient between the can and the surrounding air at 25°C is 10 W/m2 · °C, determine how long it will take for the average temperature of the drink to rise to 15°C. In an effort to slow down the warming of the cold drink, a person puts the can in a perfectly fitting 1-cm-thick cylindrical rubber insulator (k = 0.13 W/m · °C). Now how long will it take for the average temperature of the drink to rise to 15°C? Assume the top of the can is not covered.
A 2 m X 1.5 m section of wall of an industrial furnace burning gas is not insulated, and the temperature at the outer surface of this section is measured to be 80oC. The temperature of the furnace room is 30oC, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 w/oC. It is proposed to insulate this section of the furnace wall with glass wool insulation (K=0.038 W/moC) in order to reduce the heat loss by 90 percent. Assuming the outer surface temperature of the section remains at about 80oC, determine i) the thickness of the insulation that is needed and ii) the outer surface temperature of the insulation after installation.
A person puts a few apples into the freezer at 15°C cool them quickly for guestswho are about to arrive. Initially, the apples are at a uniform temperature of 20°C,and the heat transfer coefficient on the surfaces is 8 W/m2·K. Treating the apples as9-cm-diameter spheres and taking their properties to be 840 kg/m3, Cp 3.81 kJ/kg·K, k = 0.418 W/m·K, and α =10-7 m2/s, determine the center and surface temperatures of the apples in 1 h. Also, determine the amount of heat transfer from each apple. Solve this problem using analytical one-term approximation method (notthe Heisler charts). Answer: Center: 11.2 ℃, Surface: 2.7 ℃, heat transfer: 17.2 kJ
A 2-m x 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m² • °C. It is proposed to insulate this section of the furnace wall with expanded perlite insulation (k = 0.052 W/m • °C) in order to reduce the heat loss by 90%. Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used. ANSWER:_______cm
A 2-m × 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m2·C. It is proposed to insulate this section of the furnace wall with perlite insulation (k = 0.052 W/m·C) in order to reduce the heat loss by 90 percent, Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used.
A 0.8-cm-thick,15-cm-high, and 20-cm-long circuit board houses 100 closely spaced logic chips on one side, each dissipating 0.05 W. The board is impregnated with copper fillings and has an effective thermal conductivity of 20 W/m-K. All the heat generated in the chips is conducted across the circuit board and is dissipated from the back side of the board to the ambient air. Determine the temperature difference between the two sides of the circuit board.
A 40-cm-long, 800-W electric resistance heating element with diameter 0.5 cm and surface temperature 120°C is immersed in 75 kg of water initially at 20°C. Determine how long it will take for this heater to raise the water temperature to 80°C. Also, determine the convection heat transfer coefficients at the beginning and at the end of the heating process.