A refrigeration system is to be used to constantly maintain a space at -12°C in an industrial cooling space. The estimated cooling rate of 96826 kJ/h when the outside temperature is 24°C. Determine the minimum power required to drive this refrigerator if analysis is based on Carnot cycle

A refrigeration system is to be used to constantly maintain a space at -12°C in an industrial cooling space. The estimated cooling rate of 96826 kJ/h when the outside temperature is 24°C. Determine the minimum power required to drive this refrigerator if analysis is based on Carnot cycle

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 12RQ: Refrigerators currently being manufactured in the United States are using______as their refrigerant.

See similar textbooks

Related questions

Q: What is the difference between centrifugal pump and reciprocating pump ? Give at least eight points.

A: Following is the comparison between the centrifugal pump and the reciprocating pump : Centrifugal…

Q: The experimental setup for this week's lab consists of a syringe connected to a metal can…

A: Given : To find :

Q: A circular window with a radius of 0.25 m has its center 3 m below the water's surface. The window…

Q: A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm…

Q: Q1\ R22 compressed at Isentropic compression s=c, from P=0.3MPa & x-1, to P=0.7MPa, find enthalpy &…

Q: A pipe of 60 meters long and 150 mm in diameter is connected to a water tank at one end and flows…

A: A 60-meter-long, 150-mm-diameter pipe is linked to a water tank on one end and runs freely into the…

Q: As a process engineer, you are designing a new drinking water treatment plan using conventional…

Q: For the given vectors V₁ and V₂, determine V₁ + V2, V₁ + V2, V₁ - V2, V₁ X V2, V₁ V₂. Consider the…

A: Disclaimer:“Since you have posted a question with multiple sub-parts, we will solve first three…

Q: A Dynamics experiment consists of collar B (mg = 10 kg) traveling to the left at VB = 1.5 m/s on a…

Q: Turbine 6. An aircraft pulls a banner as shown below. The aircraft speed is 144 km/h. The banner is…

A: Given: Length of the banner→L=25 m Height of the banner→H=4 m Hence area of the both sides of the…

Q: A 27m3 CUBICAL TANK IS FULL OF TWO DIFFERENT FLUIDS OF EQUAL PARTS. AN OBJECT WAS THROWN AND WAS…

A: When a body is submerged partially or fully in a fluid then, it experience the upward buoyancy force…

Q: 13. A scale model of 1 is used to determine the design of a turbine to develop 10,000 B.H P. under a…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: Solve for the minimum thickness of a pressure vessel that is designed to hold gas at a pressure…

A: Given data, P=1385 psi. d=2.5 ft.= 30 in. S= 14 ksi. =14000 psi

Q: (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the…

Q: A cantilever beam 2.5 m long having T-section as shown in Fig. 9-15 carries two concentrated loads.…

A: Two focused loads are carried by a 2.5 m long cantilever beam with a T-section as shown in the…

Q: For the pasteurization process, the cold milk with a 4°C temperature value enters the first heat…

A: a) Process control elements : Controlled variable : Steam flow rate Measured variable : Temperature…

Q: A) Figure (2) shows the velocity distribution for flow of water between two parallel plates.…

A: As per honor code and answering guidelines I can answer first 3 sub parts at a time if you want…

Q: Calculate the mass of each sphere. Assume a = 3.7, b = 2.1, 0-39. y 1 aR Ꮎ Copper bR -x

Q: A single block brake, as shown, requires an operating force of 700 N. If the coefficient of friction…

Q: Compute the force in each member of the truss in Figure 1-98.

Q: Question 3 Two blocks, A and B, of mass m and 3m respectively, are connected through a cable and a…

Q: 5.8. A deep induction log is used to log a section of a 16-in. bore- hole where the mud resistivity…

Q: Consider the uniform flow of water in the triangular channel shown in the figure. The channel bed…

A: Write the expression of the normal depth. Q=1nAR2/3S

Q: iron-carbon alloy

A: According to above figure, the tabulation for Brinell hardnesses and…

Q: Determine the gravitational force F which the titanium sphere exerts on the copper sphere. The value…

Q: Diesel engine takes in atmospheric air at 101.325 kPa and 29°C. The initial volume of the air is 0.6…

A: Answer: (a) Power: 8080.6 kW (b) Efficiency: 61.2 %

Q: 0.3 m B (0) AB 12 rad/s 0.6 m 30° II IV D The velocity at point B is 3m/s towards the left. a. What…

A: given; velocity of B towards left (VB)=3m/sAB=0.3mBD=0.6mθ=300

Q: A spring with a 2-kg mass and a damping constant 8 can be held stretched 1 meters beyond its natural…

Q: Find the moment of mass from the x-axis for y = x ln(x) - 3x and y = 1 bounded by x = 3 and x = 6.…

A: Write the given data. f(x)=xlnx-3xg(x)=1limits, x=3 to x=6ρ=0.37 kg/unit2

Q: Q2-a) determine the advantages of power screw. h b-A shaft is to transmit 50 KW at 1200 rpm.. The…

Q: A constant-volume mixing tank mixes two inlet streams containing salt. The salt concentration in…

A: Given: m1 = 25 kg/s (5% salt) m2 = 10 kg/s (15% salt)

Q: The constant-pressure vary with temperature heat capacity of Cl₂, a perfect gas was found to…

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: 3. A reheat steam cycle has 13, 580 kPa of throttle pressure at the turbine inlet and a 37.50308414…

A: Given data cycle : Reheat Rankine cycleThrottle pressure = 13580 kPaTurbine inlet pressure =…

Q: Q5- If the baem shown in the Fig. (5) has a square cross section, what is their minimum required…

Q: Show the COMPLETE SOLUTIONS what is the magnitude of the total linear acceleration (in meters per…

A: The magnitude of the total linear acceleration: option (B) : 2.56 m/sec2

Q: FCP graduate who joined the Navy as a pilot is about to take off in an F-15 (WF15 = 81,000 lb) from…

A: Introduction: The constant thrust is a type of mechanical force. It is most commonly produced by the…

Q: Q2/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the…

A: Givenσx=100kPaσy=700kPaτxy=400kPa

Q: A turbine is required to generate 6-MW of electricity to serve its coverage area. If it has an…

A: Note: As per the policy, we can solve the first question from multiple questions. Please resubmit…

Q: Ixoxd 150 pints a and b of the cantilever shafts show in the figure 10 KN 2. 200

A: Given: Transverse load on the beam: →P=10 KN=10000 N Length of the shaft→L=200 mm=0.2 m Outer…

Q: At what altitude h above the north pole is the weight of an object reduced to 53% of its…

A: Given data W'=0.53 W Here, W' is the weight at height and W is the weight on the surface of the…

Q: Support forces A and B are on both ends of a 9 m long beam and another support of 400 N is acting on…

Q: Which of the following statements DOES NOT describe a fluid? a.lt stays in a constant shape upon…

Q: For the given vectors V₁ and V₂, determine V₁ + V2, V₁ + V2, V₁ - V2, V₁ × V2, V₁ V2. Consider the…

Q: Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains…

A: GivenPA=110 kN/m2S.GA=1.5S.GB=0.5PB=216 kN/m2x=2.1my=1.1m

Q: Draw and explain how the “photoelectric effect” is used in a solar panel to power up electrical…

A: The photoelectric effect occurs when electrons are ejected from the surface of solid material when…

Q: Q1- For the joint shown in Fig. (1), determine the max. safe load (P) which may be applied if the…

Q: he _______ moves the controller output as a function of the rate of change of the controlled…

A: derivative controller is used to increase its speed of response

Q: The surface tension of the water in air in approximately 0.0756 N/m. If the atmospheric pressure is…

A: It is very basic question of fluid mechanics portion. Topic- Surface tension Used concept is…

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

Q: A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the…

Question

Use 1°C=273 K if necessary.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(a) What is the hot reservoir temperature of a Carnot engine that has an efficiency of 42.0% and a cold reservoir temperature of 27.0C? (b) What must the hot reservoir temperature be for a real heat engine that achieves 0.700 of the maximum efficiency, but still has an efficiency of 42.0% (and a cold reservoir at 27.0C)? (c) Does your answer imply practical limits to the efficiency of car gasoline engines?
A completely reversible refrigerator is driven by a 10-kW compressor and operates with thermal energy reservoirs at 250 K and 300 K. Calculate the rate of cooling provided by this refrigerator
A Carnot heat engine operates between a source at 1000 K and a sink at 300 K. If the heat engine is supplied with heat at a rate of 800 kJ/min, determine the thermal efficiency.
A heat engine cycle is executed with steam in the saturation dome between the pressure limits of 7 and 2 MPa. If heat is supplied to the heat engine at a rate of 150 kJ/s, the maximum power output of this heat engine is (a) 8.1 kW (b) 19.7 kW (c) 38.6 kW (d) 107 kW (e) 130 kW
An inventor claims to have developed a heat engine that receives 700 kJ of heat from a source at 500 K and produces 300 kJ of net work while rejecting the waste heat to a sink at 290 K. Is this a reasonable claim? Why?
A food refrigerator is to provide a 15,000-kJ/h cooling effect while rejecting 22,000 kJ/h of heat. Calculate the COP of this refrigerator.
Calculate the thermal efficiency of a Carnot cycle heat engine operating between reservoirs at 300°C and 45°C.
A heat engine is operating on a Carnot cycle and has a thermal efficiency of 78 percent. The waste heat from this engine is rejected to a nearby lake at 60°F at a rate of 800 Btu/min. Part A Determine the power output of the engine. UNITS IN (hp) Part B Determine The temperature of the source in (R) Make sure you use the correct units PART A in (hp) and Part B in (R)
Prove that the COP of all completely reversible refrigerators must be the same when the reservoir temperatures are the same.
Explain the principle of refrigerator? Show that a reversible heat engine acts as a refrigerator.
It is claimed that a certain cyclical heat engine operates between the temperatures of TH = 448°C and TC = 155°C and performs W = 3.98 MJ of work on a heat input of QH = 4.97 MJ. a. How much heat, in megajoules, would be discharged into the low-temperature reservoir? b. Which choice, by itself, is unreasonable about the claim? 1. The efficiency is greater than the Carnot efficiency for the stated temperatures 2. The work performed is less than the heat input. 3. The temperature difference is greater than 273.15 K. 4. All of these. 5. None of these
What is cyclic Heat engine? What is the difference between refrigerator and heat Pump?