A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum twist allowed in a 3m length of shaft is 1.5 degrees. If the maximum torque is 30% more than the average or mean torque. Assume a fully elastic action and a modulus of rigidity of G=135 GN/m2 for the shaft material. Calculate the shaft's diameter and the shaft's maximum shear stres

A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum twist allowed in a 3m length of shaft is 1.5 degrees. If the maximum torque is 30% more than the average or mean torque. Assume a fully elastic action and a modulus of rigidity of G=135 GN/m2 for the shaft material. Calculate the shaft's diameter and the shaft's maximum shear stres

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
15 mm diameter shaft rotates in long fixed bearings 60 cm apart. A rotor of mass 20 kg is mounted at mid span. The mass center of rotor is 0.5 mm from the shaft axis. If the bending stress in the shaft is not to exceed 120 MPa. Find range of speed over which the shaft must not run. Take modulus of elasticity for the shaft material as 200kN/m².
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.
A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed that the shaft twists 1.5° in a length of 5 metres at 500 r.p.m. The shaft is solid and has a diameter of 200 mm. If the modulus of rigidity for the shaft material is 85 GPa, find the power transmitted by the turbine.
Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1 meter long shaft with a permissible shear stress of 320 MPa G=80 GPa
A shaft with a length of 2 m has the cross section shown in Figure 1, where a = 4 cm and t = 4 mm. Calculate the torsional bending constant Γ of the shaft. If only one end is allowed to warp, calculate the relative angle of rotation between the two ends of the shaft with a torque of 200 Nm. Assuming the material is isotropic, E = 200 Gpa, υ = 0.3.
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
A hollow shaft with external and internal diameters 100 mm and 75 mm respectively transmits 500 kW at 1 500 r/min. If the measured angle of twist in a length of 3,5 m is 1,17°, calculate the shear strain at the inner and outer radii and the modulus of rigidity of the shaft material.
A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm respectively and transmits 8000 kW at 100 r/min. Calculate the maximum shear stress in the hollow shaft. Calculate the shear stress on the inner surface of the hollow shaft. Determine the maximum length of this shaft if the maximum shear stress as well as an angle of twist of 30 is not to be exceeded. (G = 80 GPa) If this shaft is connected to a similar shaft, 1 m long, through a 10-bolt rigid flange coupling, determine the minimum standard bolt diameter if the pitch circle diameter of the coupling is pcd = 450 mm and the allowable shear stress in the bolts should not exceed 55 MPa. Determine the equivalent torsional stiffness of the shaft assembly.
A hollow shaft and a solid shaft constructed of the same material have the same length and the same outer radius. The inner radius R of the hollow shaft is 0.6R. Assuming that both shafts are subjected to the same torque, compare their shear stresses, angle of twist and weights.
A shaft has an external diameter (ED) of 350 mm and an internal diameter of 150 mm. i. Calculate the maximum shear stress in the shaft when it is transmitting 3700 kW at 100 rpm. ii. Find the angle of twist in a length of 20 x ED. (Assume G=75GN/m2). iii. If the hollow shaft is replaced by a solid shaft of the same weight and length, what power can it transmit for the same maximum shear stress?