. A certain parallel-plate capacitor is filled with a dielectric for which of each plate is 0.0726 m?, and the plates are separated by 1.13 mm. The capacitor will fail (short out and burn up) if the electric field between the plates exceeds 217 kN/C. What is the maximum energy that can be stored in the capacitor? = 4.58. The area

. A certain parallel-plate capacitor is filled with a dielectric for which of each plate is 0.0726 m?, and the plates are separated by 1.13 mm. The capacitor will fail (short out and burn up) if the electric field between the plates exceeds 217 kN/C. What is the maximum energy that can be stored in the capacitor? = 4.58. The area

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter8: Capacitance

Section: Chapter Questions

Problem 61P: The dielectric to be used in a parallel-plate capacitor has a dielectric constant of 3.60 and a...

See similar textbooks

Similar questions

The dielectric to be used in a parallel-plate capacitor has a dielectric constant of 3.60 and a dielectric strength of 1.60107 V/m. The capacitor has to have a capacitance of 1.25 nF and must be able to withstand a maximum potential difference 5.5 kV. What is the minimum area the plates of the capacitor may have?
(a) Regarding (lie Earth and a cloud layer 800 m above the Earth as the plates of a capacitor, calculate the capacitance of the Earth-cloud layer system. Assume the cloud layer has an area of 1.00 km2 and the air between the cloud and the ground is pure and dry'. Assume charge builds up on the cloud and on the ground until a uniform electric field of 3.00 106 N/C throughout the space between them makes the air break down and conduct electricity as a lightning bolt, (b) What is the maximum charge the cloud can hold?
When a potential difference of 150. V is applied to the plates of an air-filled parallel-plate capacitor, the plates carry a surface charge density of 3.00 1010 C/cm2. What is the spacing between the plates?
The three charged particles in Figure P25.22 are at the vertices of an isosceles triangle (where d = 2.00 cm). Taking q = 7.00 C, calculate the electric potential at point A, the midpoint of the base.
At a certain distance from a charged particle, the magnitude of the electric field is 500 V/m and the electric potential is 3.00 kV. (a) What is the distance to the particle? (b) What is the magnitude of the charge?
A filament running along the x axis from the origin to x = 80.0 cm carries electric charge with uniform density. At the point P with coordinates (x = 80.0 cm, y = 80.0 cm), this filament creates electric potential 100 V. Now we add another filament along the y axis, running from the origin to y = 80.0 cm. carrying the same amount of charge with the same uniform density. At the same point P, is the electric potential created by the pair of filaments (a) greater than 200 V, (b) 200 V, (c) 100 V, (d) between 0 and 200 V, or (e) 0?
A parallel-plate capacitor with capacitance C0 stores charge of magnitude Q0 on plates of area A0 separated by distance d0. The potential difference across the plates is V0. If the capacitor is attached to a battery and the charge is doubled to 2Q0, what are the ratios (a) Cnew/C0 and (b) Vnew/V0? A second capacitor is identical to the first capacitor except the plate area is doubled to 2A0. If given a charge of Q0, what are the ratios (c) Cnew/C0 and (d) Vnew/V0? A third capacitor is identical to the first capacitor, except the distance between the plates is doubled to 2d0. If the third capacitor is then given a charge of Q0, what are the ratios (e) Cnew/C0 and (f) Vnew/V0?
Figure P26.44 shows a rod of length = 1.00 m aligned with the y axis and oriented so that its lower end is at the origin. The charge density on the rod is given by = a + by, with a = 2.00 C/m2 and b = 1.00 C /m2. What is the electric potential at point P with coordinates (0, 25.0 cm)? A table of integrals will aid you in solving this problem.
Two point charges, q1 = 2.0 C and q2 = 2.0 C, are placed on the x axis at x = 1.0 m and x = 1.0 m, respectively (Fig. P26.24). a. What are the electric potentials at the points P (0, 1.0 m) and R (2.0 m, 0)? b. Find the work done in moving a 1.0-C charge from P to R along a straight line joining the two points. c. Is there any path along which the work done in moving the charge from P to R is less than the value from part (b)? Explain.
A 60.0-pF vacuum capacitor has a plate area of 0.010 m2. What is the separation between its plates?
(a) Calculate the electric potential 0.250 cm from ail electron, (b) What is the electric potential difference between two points that are 0.250 cm and 0.750 cm from an electron? (c) How would the answers change if the electron were replaced with a proton?
A filament running along the x axis from the origin to x = 80.0 cm carries electric charge with uniform density. At the point P with coordinates (x = 80.0 cm, y = 80.0 cm), this filament creates electric potential 100 V. Now we add another filament along the y axis, running from the origin to y = 80.0 cm, carrying the same amount of charge with the same uniform density. At the same point P, is the electric potential created by the pair of filaments (a) greater than 200 V, (b) 200 V, (c) 100 V, (d) between 0 and 200 V, or (e) 0?