. A well-insulated piston-cylinder device contains 5 L of saturated water at a constant pressure of 150 kPa. Water is stirred by a propeller connected to a 500 W motor while a power source that supplied 8A of electrical current flow through the coil. The propeller and coil are placed in the water for which they are switched ON for 38 minutes. If one-half of the mass of liquid is vaporized to saturation in this process, determine (a) is this nonflow or steady flow process? (b) draw the pv and Ts diagrams (c) voltage of power supply, and (d) using the same power supply as calculated in (c), how long it will take in minutes if the device is not insulated so that heat loss is 400 kJ? 5 answers in BOXES

. A well-insulated piston-cylinder device contains 5 L of saturated water at a constant pressure of 150 kPa. Water is stirred by a propeller connected to a 500 W motor while a power source that supplied 8A of electrical current flow through the coil. The propeller and coil are placed in the water for which they are switched ON for 38 minutes. If one-half of the mass of liquid is vaporized to saturation in this process, determine (a) is this nonflow or steady flow process? (b) draw the pv and Ts diagrams (c) voltage of power supply, and (d) using the same power supply as calculated in (c), how long it will take in minutes if the device is not insulated so that heat loss is 400 kJ? 5 answers in BOXES

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the enthalpy of steam at 127C, at 75% quality, and flowing at the rate of 70 kg/h, if it isused to heat fluid soup. What is the volume in m3 of steam required per hour of operation?
Consider two cases of vaporization of a saturated liquid to saturated vapor at constant pressure of 102.7 kPa and 506.8 kPa. Which case requires more energy? show all necessary calculations
Complete the blank cells in the following table of properties of steam. In the last column, describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information, and, if applicable, give the quality
For the situations below briefly explain how you obtained the values and provide the numerical answer. A) When 1 kg saturated water vapor is condensed to a saturated liquid water at 325 Kpa, what is the change in its volume? B) What is the specific internal energy liquid water at 280 degree Celsius and 7500 Kpa?
Explain T-v diagram of constant-pressureb phase-change processes of a pure substance at various pressures 0.003106 (numerical values are for water).
Water is boiled at sea level in a coffeemaker equipped with an immersion-type electric heating element. The coffeemaker contains 1 L of water when full. Once boiling starts, it is observed that half of the water in the coffeemaker evaporates in 13 min. Determine the power rating of the electric heating element immersed in water. Also, determine how long it will take for this heater to raise the temperature of 1 L of cold water from 18°C to the boiling temperature.
A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400°C. Determine the heat added in kJ.
The average atmospheric pressure in Denver (elevation = 1610 m) is 83.4 kPa. Determine the temperature at which water in an uncovered pan boils in Denver.
How did you determine the properties of water at state 3?
A 2-m3 rigid vessel contains helium initially at a gage pressure and temperature of 320 kPa and 315 K respectively. Because of the leaks in the fittings of the vessel, the gage pressure dropped to 280 kPa and the temperature decreased to 300 K, determine the mass of the helium that leaked out and also the mass of nitrogen that remained in the vessel. (Ans. 0.06399 kg, 1.2240 kg)
At 50 ° C and 900 kPa pressure, 2 kg of superheated steam refrigerant -134a is cooled at constant pressure until half of it condenses. a) This process is done by paying attention to the saturation lines in T-v and P-v diagrams show. b)Calculate the change in volume.
Saturated vapor at 60°C is put under pressure to decrease the volume by one percent during an isothermal process. Determine the change in internal energy in kJ if the mass of vapor is 7.089 kg.