. One end of a steel rod of radius R = 9.5 mm and length L = 81 cm is held in a vise. A force of magnitude F =62 kN is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What is the stress on the rod and the elongation AL and strain of the rod?

. One end of a steel rod of radius R = 9.5 mm and length L = 81 cm is held in a vise. A force of magnitude F =62 kN is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What is the stress on the rod and the elongation AL and strain of the rod?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 50PQ

See similar textbooks

Similar questions

Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Can Young’s modulus have a negative value? What about the bulk modulus?
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
The bulk modulus of a material is 1.01011N/m2 . What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 107N/m2 ? Assume that the force is applied uniformly over the surface.
Review the relationship between stress and strain. Can you find any similarities between the two quantities?