.Describe the impact action of a Multi pair punch terminating tool?

Q: Data has been gathered from a lifting system used to remove spent RBMK fuel rods from the spent rod ...

A: Solution: Given Data: Time taken to lowered into concrete barrels = 10 Seconds Winch drum diameter =...

Q: The force system acting on the machine part is equivalent to the single force R=80i + 20jlb acting a...

A: Given data: R=80i+20j Need to determine the force P and the distance b.

Q: 4. The uniform slender rod AB shown of weight W is supported by a peg at C and its end A rests again...

A: Solution: Given Data: θ=30of=0.3

Q: Air with cv = 0.723 KJ/Kgm - °R is compressed in a piston-cylinder machine according to pV1.3 = c fr...

A:

Q: A planar mechanism has 8 links and 10 rotary joints. The number of degrees of freedom of the mechani...

A:

Q: Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip? a.Standard...

A: Given Data : Screwdrivers Phillips

Q: A transmission tower is held in place by bolts at B, C, and D. If the force on the cable AD is 664 N...

A:

Q: n air at 25°C and latm. Use drag coefficient Cp = 0.4 and Whitak e spheres fall at their terminal ve...

A: we know thatRe=ρuDμ=uDνwhere,Re=Reynolds number          ρ= density         D=  diameter         u=v...

Q: Which of the following angles a ball will reach the maximum height if it is thrown in the absence of...

A:

Q: f flyewheel is collached fo to keep its fefational speed between engice 9o radls tollorádl /s f Ahe ...

A: GIVEN DATA- ∆E=0.01KJ ω1 = 110 rad/s ω2 = 90 rad/s WE HAVE TO FIND MASS MOMENT OF INERTIA

Q: Determine whether the series converges.

A: NEED TO DETERMINE THE TYPE OF SERIES.

Q: Write short notes on: (i) Gear pump (ii) Lobe pump (iii) Screw pump

A:

Q: explanations for each selection of your anthropometric values

A: Anthropometrics are a bunch of harmless, quantitative body estimations used to. evaluate development...

Q: When a hydrocarbon fuel is burned, almost all of the carbon in the fuel burns completely to form CO2...

A: 0.59 kg of CO2 is produced for each kWh of electricity generated from a power plant that burns natur...

Q: Determine pin reaction at A & C as shown in (Fig.)? 2 kN 2 60

A: Find the reactions at point A and point C

Q: 2. IN ARANKINE CYCLE, SATURATED LIQUID WATER AT 1 BAR IS COMPRESSED ADIABATICALLY TO 150BAR. FIRST B...

A:

Q: At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compres...

A:

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Qout = 250 kJ. Determine Qin in kJ.

A: Answer: Oin = 1250 kJ.  

Q: Draw Head –Capacity curve of centrifugal pump at varying pumping speeds.

A:

Q: The non-zero value of @,

A: Given; A single-degree of freedom oscillator is subjected to harmonic excitation  Ft=F0cosωts shown ...

Q: In a well designed wing, which of the following would best describe the lift to drag ratio? O a. Itw...

A:

Q: -400N -400N 600 -33.7mm -25.7mm 1250 0007 00 1200 009 006 006 001

A: STRESS While the disfiguring force is applied to an item, the article twists. To take the article ba...

Q: A bar of size 3m long, 250 mm wide and 150 mm thick is subjected to pull of 50 kN. Find change in le...

A: Given data as per question Length of bar=3mwidth of bar=250mmthickness=150mmPulling force =50 kNE=2×...

Q: Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation...

A:

Q: A copper alloy pipe with a yield stress σY = 290 MPa is to carry an axial tensile load P = 1500 kN (...

A:

Q: A particle moves from P (6,-2,-1) to Q (4,-1,1) under the action of a force F = 2î +4j+ 5k. What is ...

A: second part of the text has no relation with first part. so I am solving the first question which is...

Q: 35 mm 10 kN-m 2.36 x10° mm* G1 = 70 GPa (1) 40 mm C2 = (2) 4.02 x106 mm B 45 GPa 2800 mm 3600 mm A c...

A: GIVEN DATA- A COMPOSITE SHAFT GIVEN C1=35mm J1=2.36*10^6 mm^4 G1=70GPa C2=40mm J2=4.02*10^6 mm^4 G2=...

Q: Two chambers with the same fluid at their base are separated by a 30-cm- diameter piston whose weigh...

A:

Q: "A thermodynamic process from state A to state B is a vertical line path in the PV diagram. This pro...

A:

Q: x axis value  of the centroid of the shape below with respect to an x and y axis with origin at the ...

A:

Q: The atmospheric pressure P decreases exponentially with elevation k as follows, P(h) = Poe-ah/a ,whe...

A: The SI Unit of A is m2/s2.

Q: 2) Three cylinder A:B:C has a speed ratio of 3:2:4 are externally in contact to each other. If cente...

A:

Q: 90

A:  data we have    given P =100 kgm2      Ab = 25m/s2   massm =P×area                 = 100 kgm2×πr2  ...

Q: Consider a tank with surface area A.(m2) It containsa fluid of M(kg) at an initial temperature of T0...

A: Given: surface area of the tank = A m2 mass of the fluid = M Kg initial temperature =To°C Specific h...

Q: A soccer referee inflates a soccer ball to the standard required measured pressure for a game of 90k...

A:

Q: The pipes at A and B contain oil and the inclined tube manometer is filled with oil and mercury. Det...

A:

Q: A venturi meter is used to measure liquid flow rate of 450 m3 /h. The difference in pressure across ...

A: Answer: The throat diameter is 11.20 cm.  

Q: A hot water pump pumps water from a tank (known as the condenser) up to a storage tank- boiler. The ...

A:

Q: Write down berniullis equation

A: It is required to write Bernoulli equation

Q: Hazel stands on the edge of a lookout admiring the view of a waterfall. The lookout is supported by ...

A: Givenmass m=60kgg=9.81m/s2θ=700

Q: (a) Find the cat's initial velocity, initial position, and initial acceleration. (b) At what time is...

A:

Q: Q13. As shown in the image below, the 54 kg-crate is initially at rest, and at a distance d = 6.0 m ...

A: Given data: m=54 kgμk=0.22d=6 mk=1.3 kN/m=1300 N/mg=9.81 m/s2vi=vf=0 Need to determine the compressi...

Q: A four-wheel drive vehicle has a front solid drive axle suspension and a rear solid drive axle suspe...

A: Solution: h = 20.5 in L = 108.5 in r = 15 in

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls...

A:

Q: The following data are obtained from a tensile test of a copper specimen. The load at the yield poin...

A: Since you have asked a question with multiple parts in a single request we would be answering only t...

Q: 14) A cam operating roller follower has the following dimensions, radius of base and nose circle as ...

A: As per student request I am answering 14th question 

Q: 25 kN 20 kN 20 kN 75 mm

A:

Q: Boxes are transported by a conveyor belt with a velocity voto a fixed Incline at A where they slide ...

A:

Q: e number of instant center and locate all of them using IC Circle method. ea software to visualize t...

A:

Q: Using the DE-Goodman criteria and a design factor of 1.5, calculate the diameter based on the shaft...

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.