Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation speed of gear 1 is n₁=380 r/min, calculate the rotation speed of gear carrier H

Q: explanations for each selection of your anthropometric values

A: Anthropometrics are a bunch of harmless, quantitative body estimations used to. evaluate development...

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Wnet = 250 kJ. Determine Qout in kJ. Ent...

A: Given data,  n= 0.8  Qout= required Wnet= 250 kJ

Q: a steel train rail is 400 meters long, in march it is -30°C and 40°C in july. what is the change in ...

A: Given: L = 400 m T1 = -30 deg C T2 = 40 deg C Correct answer: (c) 328 mm

Q: 6) The number of degrees of freedom of a planar linkage with 8 links and 9 simple revolute joints is

A: Given:number of links, l=8number of joints, j=9

Q: Drive Shaft Outlet Blades Inlet Scroll Impeller

A: IMPELLER FAN A fan impeller is ordinarily joined to the turning shaft. Outer rotor engines basically...

Q: When a hydrocarbon fuel is burned, almost all of the carbon in the fuel burns completely to form CO2...

A: 0.59 kg of CO2 is produced for each kWh of electricity generated from a power plant that burns natur...

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: Calculate the Mach number, pressure, temperature and velocity of the gas downstream of the shock.

A: For Downstream of the shock:   Mach Number: M2=(γ+1)M22+(γ-1)M2=(1.3+1)2.522+(1.3-1)2.52=14.3753.875...

Q: Water drains from a pressurized tank (50 kPa gage) through a 0.1m-diameter pipe system at a rate of ...

A: GIVEN DATA- Q=0.0371 m3/s L=200m d=0.1m P=50KPa WE HAVE TO FIND VELOCITY IN PIPE

Q: reaction, blading has isentropic efficiency of 82%. It draws air at 17 °C and compresses in the pres...

A:

Q: King Orquinaza bought a diesel electric plant in a remote part of Ilo-Ilo province that utilizes die...

A:

Q: 11) In a crank-rocker (four-bar linkage), s denotes the shortest link length, L the longest link len...

A: To determine the condition for given motion.

Q: "A thermodynamic process from state A to state B is a vertical line path in the PV diagram. This pro...

A:

Q: Here, a liquid's density is to be determined by a 1-cm diameter cylindrical hydrometer whose divisio...

A:

Q: A single-degree-of-freedom oscillator is subjected to harmonic excitation F(t) = F, cos(ot) %3D as s...

A:

Q: Pin C is attached to rod BC and slides in the slot of rod OA. The rod BC rotates at a constant rate ...

A:

Q: 3 kN/m. EN. A Ay Draw 6 m zm. S.F. 9 B.M.5 shear force and bending moment diagram

A:

Q: 5. The combined drive wheels of a front - wheel - drive automobile are acted on by a 7000 N normal r...

A:

Q: Define the meaning and significance of the ductile to brittle transition temperature (DBTT). Identif...

A: DBTT: A temperature at which there is abrupt change in the ability of material to absorb force witho...

Q: A wire of length 2.5 m has a percentage strain of 0.012% when loaded with tensile force. Determine t...

A: Given Data L=2.5 m

Q: intrinsic semiconductor ong extended defect in a crystal

A: solution of above equation is below:  

Q: 4. The analyst in the Red Diamond Electronics Company wishes to assign a number of like facilities t...

A: Given data: l=0.34+0.26=0.6 minutesm=1.48 minutesC1=$12 per hourC2=$18 per hourw=0.06 Need to determ...

Q: A planar mechanism has 8 links and 10 rotary joints. The number of degrees of freedom of the mechani...

A:

Q: METHODS OF RESEARCH

A: Given Research To find Fundamental research Quantitative Research Qualitative Research

Q: n end force of 15 kN inc rot or go

A:

Q: 4) The criterion of constraints for a kinematic chain having plane motion is given by the equation:

A: Solution to Q4 as mentioned by the student:

Q: Liquid mercury flows at 1.6kg/s through copper tube of 20mm diameter. The mercury enters tube at 15°...

A:

Q: A cylinder of mass m, radius r and radius of gyration k is released from rest and rolls without slip...

A:

Q: Required: i. Change in length if the rod is heated to 200°C. ii. Change in diameter if T; = 200°C. i...

A:

Q: A heat pump operates with Qin = 100kJ and Qout=250kJ. The cycle work is

A: Given data: Qin=100 kJQOut=250 kJ Need to determine the cycle work.

Q: A Pelton wheel develops 1800 kW under a head of 120 m while running at 210 rpm and discharging of 2....

A:

Q: meter. ler A:B:C has a speed ratio of 3:2:4 are externall ter distance between cylinder A and C is 3...

A:

Q: 10. Atmospheric pressure, Stau 11. Atmospheric pressure, stated in psig, is 12. Atmospheric pressure...

A: 10. 14.7 psi 11. 0 psi (14.7-14.7) 12. 29.9212 in Hg 13. above and below 14. inversely as long as th...

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum tensile ...

A:

Q: Hwe, Find the system stability par th Ch qpe Por 4 3 2 is as : S+25+4S+85 +lo =D0

A: Since there are two sign changes in the first column of the Routh array, the system is unstable.

Q: The total emissive power of a surface is 500 W/(m ^ 2) at a temperature T1, and 1200 W/(m ^ 2) at a ...

A: Givenemissive power E1=500 W/m2 at T1emissive power E2=1200 W/m2 at T2

Q: the convective heat transfer coefficient

A: Given: A small metal bead, has radius, r=0.5 mm Initially temperature at, T=1000 CWhen placed at str...

Q: Write down the operating principle of Venturi meter.

A: Venturi Meter: Venturi Meter is a mechanical device which is used to determine flow rate of a fluid ...

Q: Activity 1. For the truss shown in the figure, determine the forces acting on members AB, AC,BC,CE b...

A: For a step-by-step solution have a look through the attached pictures of the solution. The required ...

Q: Points R and S have position vectors (10,2,4) and (2,0,5) respectively. Find the vector RS.

A:

Q: 3. A 100 m length of smooth horizontal pipe is attached to a large reservoir. What depth d, must be ...

A:

Q: 1000mm Input shaft A 100mm Bearing support 200mm 450mm pulley pulley 200mm 150mm 450mm pulley Bearin...

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost...

Q: Why does a turbine blade which breaks during the operation of an aeroengine need to be contained wit...

A: During the operation of aerodynamics there is very high speed in very very high altitude. If the bro...

Q: the length of the link PQ?

A: Given: A crank-rocker mechanism, QR=700 mm SR=200 mm  SP=350 mmLength og the link PQ ?

Q: 1) Two parallel shaft connected by pure rolling turn in the same direction and having a speed ratio ...

A: Given:SR=2.75dp=22 cm

Q: What is the equivalent height of a fluid having an SG of 10 in barometer with a pressure of 101.325k...

A: Given data,  P= 101.325 KPa =101.325*1000 Pa SG = 10  Need to find h

Q: What is zeroth law of thermosynamics

A: The zeroth law of thermodynamics states that if two system are in thermal equilibrium with a third s...

Q: Which of the ff are methods to adjust the gaps in centerlines ¢er marks? A. Center B. Center2 C. Cen...

A: Different types of lines used in AutoCAD are: Continues line Center Line Hidden Line

Q: 12) The lengths of links of a 4-bar linkage with revolute pairs only are p, q, r and s units. Given ...

A: Dear student,                     According to the guidelines I am allowed to answer only one proble...

Q: material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using gr...

A: TgfffgahHha

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.