0/ Consider a closed-loop transfer function is: Y(s) R(s) s +a,s+a, %3D From its below response to a unit step input, find the damping ratio (), undamped natural frequency (o,), damped natural frequency(o), peak time (t,), rise time (t,), and steady state value (y,,) if the input is a unit step. 1.4 0.8 0.6 0.4 0.2 10 Time Isl

0/ Consider a closed-loop transfer function is: Y(s) R(s) s +a,s+a, %3D From its below response to a unit step input, find the damping ratio (), undamped natural frequency (o,), damped natural frequency(o), peak time (t,), rise time (t,), and steady state value (y,,) if the input is a unit step. 1.4 0.8 0.6 0.4 0.2 10 Time Isl

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Difference equation of a discrete-time causal (right-sided) LTI system, y(n) = 2 x(n) – x(n-1) -1/4 y(n-1) + 1/8 y(n-2) is given as. a) Give the system function H(z). b) Indicate zero, poles and ROC in the Z-plane. Is the system stable? Please explain. c) Find the impulse response of the system. d) If the system is left-sided, repeat (b) and (c).
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
For the circuit shown below, the initial conditions are zero, Idc is a current source continuous and switch S is open at t = 0.a)Determine the equivalent impedance to the right of points a and b of the circuit, Z(s).b)Obtain the voltage between points a and b of the circuit in the frequency domain, V(s). Employ the initial and final value properties and calculate the values of v(0) and v(∞).c)Find the expression for v(t). Check that the values of v(0) and v(∞) agree with those calculated in the previous item.d)Obtain currents i1(t) and i2(t).
Solve All parts or will dislike answer A. Find the open-loop transfer function . Y(S) / R(S)B. Find ?(?) when the input ?(?) is a step function (use expansion of partial fractions).C. State the damping factor ?.D. Indicate whether the system is overdamped, underdamped, or critically damped.E. Indicate the natural frequency of the system ??.F. Indicate the poles and zeros of the system.G. Use the end theorem to find the steady-state value.H. Find ?(?) (use inverse Laplace transform).I. Plot the time response of the system.
At t=0, a 1 pound force, denoted by f(t), is applied to the translational mechanical system. Determine K and M such that the response has a 1 second peak time and 4 second settling time if fv = 1. Additionally, what is the resulting overshoot percentage? Determine also the resulting transfer function as well as the steady state error for step input.
For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
Calculate the range of values K will take for the steady-state error to be ??? ≤ 0.04 when the input of the system is ?(?) = ?. Calculate the range of values K will take for the damping ratio to be 1>ξ ≥(1/2√6). Calculate the damping rate ξ and the undamped natural frequency ?? so that ? = 0.5
The system function of a discrete-time causal LTI system is H(z) = z / (z2 +1.5 z -1) a) Show the poles/zeros and the ROC in the Z-plane. Is this system stable? Explain. b) Calculate the impulse response h(n). c) Give the difference equation of this system. d) Repeat questions (a), (b), (c) if this system is changed to be stable.
The equation below gives the closed-loop transfer function of a system. Consider unit step response and resolve Y(s) into its partial fractions. Determine the step response for the system (y(t) = ?) 3- Use the final value theorem to determine the steady-state error (ess).
The impulse response of an LTI system is h(n) = 3δ(n) + (1/4)n u(n). Find the frequency response, H(e jω), and the difference equation of this system. An input signal x(n) = (1/3)n u(n), is applied to this system and an output signal y(n) is observed. Find the output signal, y(n), using DTFT methods. Give the system function H(z) using the frequency response H(ejω). Find the zeros, poles and ROC of this system and show them on the complex plane. Discuss the stability, causality, FIR/IIR and memory properties of this system.