Problem 02. Consider the closed-loop system with measurement noise N(s) as shown in the below figure R(s) Gels) Gp(s) Y (s) H,(s) - N(s) where 10 Ge(s) = K1 Gp(s) = K2 H,(s) %3D s+ 10' s+ 100 Compute the transfer function Y(s)/N(s) and determine the steady-state tracking error due to a unit step disturbance response, that is, let N(s) = 1/s and assume that R(s) = 0. Remember, in this case, the desired output is zero.

Problem 02. Consider the closed-loop system with measurement noise N(s) as shown in the below figure R(s) Gels) Gp(s) Y (s) H,(s) - N(s) where 10 Ge(s) = K1 Gp(s) = K2 H,(s) %3D s+ 10' s+ 100 Compute the transfer function Y(s)/N(s) and determine the steady-state tracking error due to a unit step disturbance response, that is, let N(s) = 1/s and assume that R(s) = 0. Remember, in this case, the desired output is zero.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Perhaps surprisingly, we can apply the transfer-function concept to mechanical systems. Suppose we have a mass m moving through a liquid with an applied force f and velocity v. The motion of the mass is described by the first-order differential equationf=m dv dt +kv in which k is the coefficient of viscous friction. Find an expression for the transfer functionH( f )= V F Also, find the half-power frequency (defined as the frequency at which the transfer function magnitude is 1/2 times its dc value) in terms of k and m.
b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
Examine the closed loop stability of a system whose open-loop transfer function is given by.G(s) H(s) =1+4s/s^2(1+s )(1+2s) use nyquist plot
The impulse response of an LTI system is h(n) = 3δ(n) + (1/4)n u(n). Find the frequency response, H(e jω), and the difference equation of this system. An input signal x(n) = (1/3)n u(n), is applied to this system and an output signal y(n) is observed. Find the output signal, y(n), using DTFT methods. Give the system function H(z) using the frequency response H(ejω). Find the zeros, poles and ROC of this system and show them on the complex plane. Discuss the stability, causality, FIR/IIR and memory properties of this system.
Given the signal flow graph, apply Mason’s Rule to acquire the single transfer function, G(s). Express your transfer function in a form where the coefficient of the highest exponent of s in the denominator is equal to 1. If there is a numerical answer that is nonterminating, it should be expressed up to three (3) decimal places only.
For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
Consider the following transfer function: G(s)=Y(s)/U(s)=3e−s/{10s+1} (a)What is the steady-state gain? (b)What is the timeconstant? (c)If U(s)=4/s, what is the value of the output y(t) when t→∞? (d) For the same input, what is the value of the output when t=10? What is the output when expressed as a fraction of the new steady-state value? (e)If U(s)=(1−e−s)/s, the unit rectangular pulse, what is the output when t→∞? (f)If u(t)=δ(t), the unit impulse at t=0, what is the output when t→∞?(g)If u(t)=5 sin 2t, what is the value of the output when t→∞
Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
PleaseThe input-output relationship of a discrete-time LTI system is given as follows?[n] = 2x[n − 4] − 3x[n − 6].a) Determine the impulse response of the system, h[n].b) Using h[n], show that the system is causal.c) Using h[n], show that whether the system is BIBO stable or not.d) Determine the transfer function H(z). Plot pole-zero diagram. Indicate ROC.e) Using H(z), show that whether the system is stable or not.f) Determine the frequency response of the system, if exists. Why?g) Determine the impulse response of the inverse system calculated in f).
A stable input signal x(n) is applied to an LTI system with unit impulse response h(n)=2δ(n)+ (1/2)'' u(n), and the output is y(n)=2(1/4)'' u(n) is obtained.a) Find the frequency response, H(ejw), of the system.b) Find the x(n) sign and spectrum applied to the input by DTFT.c) Give the input/output differential equation of the system.
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
A hard disk drive (HDD) is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. Figure 1 shows a simplified block diagram of a HDD. For analysis purposes, given gain K=30 and G(s)=1 / s(s+4) determine the open-loop and closed loop poles of the HDD and plot these separately in the S-Plane. Also discuss the stability using two different approaches.