1.4 Exercise Consider the closed-loop system defined by C(s) R(s) s + 2{s +1 2 (The undamped natural frequency w, is normalized to 1.) Plot unit-step response curves e(t) when z assumes the following values: -0, 0.3, 0.6, 0.9, 1.0,1.2,2 Also plot a three-dimensional plot

1.4 Exercise Consider the closed-loop system defined by C(s) R(s) s + 2{s +1 2 (The undamped natural frequency w, is normalized to 1.) Plot unit-step response curves e(t) when z assumes the following values: -0, 0.3, 0.6, 0.9, 1.0,1.2,2 Also plot a three-dimensional plot

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

From a compliance transfer function of a spring-mass–damper system, the stiffness is determined to have a value of 0.6 N/m, a natural frequency of 0.50 rad/s, and a damping coefficient of 0.089 kg/s.1. Neatly derive the expressions of the magnitude and phase of the mobility transfer function
Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
A car was ignited & a signal from the engine i.e a(z) was passed through a cascade of 2 passive RC lowpass filters to generate an output signal, b(z).a.Show a differential equation derivation to describe the systemb.Make a sketch utilizing circuit diagramc.Mention if the RC system in question above isi.Time in-variant / Time variant ii.Non linear / lineariii.Non-invertible / Invertibleiv. Non-causal / Causal v. Have no memory / Have memory sytems.d. d2b(z)/dz2 + 3(db(z)/dz) +2b(z) = 3(da(z)/dz) +2a(z)Let's assume that the d.e(differential equation) above is that which is characterised by the RC system in the main question above.Where a(z) & b(z) is the input & output of the RC system respectively.Considering an impulse of a(z)=δ(z) is applied to the system, determine the output b(z) of the system
The closed-loop transfer function of a system is given by G(s) = 14.145 / (s+5)*(s^2 +0.842s+2.829). Which of the following is true for this system? I. The damping ratio is given by 0.25. II. Its natural frequency is given as 1.682 r/s. III. Exceeding the percentage is given with 44.4%. IV. The peak time is given as 1.93 s. a) I only b) I, II, II and IV c) II and III only d) I, II and IV only
For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
Consider the mechanical system shown; m is the mass of the body, bis the damping coefficient, k is the stiffness of the spring and F is the applied force. 1) Write the differential equation for the system 2) consifer the force, F, is the input and the displacement of the body of mass, m, is the output of the system. White the transfer function for the system. 3) A proportional controller Kp is applied. Draw the closed loop block diagram for the system. 4)Write the closed loop transfer function for the system with controller Kp.
control systems In the electromechanical system given below, it can be seen that the coil can be represented by the series R-L circuit and also the coil It is known that the electromagnetic pulling force (F) is also proportional to the coil current, that is, F = βi. The input of the system is the voltage v applied to the coil and the output is the x path taken by the core. Accordingly, the system find the differential equations and transfer function
Given a plant P(s)=−3s+1s+a and a model for measureable output disturbance d with transfer function Q(s)=1s+b. Compute the DC feedforward solution uP=u+Fd, where u is the feedback control, F is the feedforward gain, abd uP is the plant input, when a = 4.3 and b = 3 (use 2 decimals).
For the circuit shown below, the initial conditions are zero, Vdc is a voltage source continuous and switch S is closed at t = 0.a)Determine the equivalent impedance to the right of points a and b of the circuit, Z(s).b)Obtain the input current of the circuit in the frequency domain, I(s). employ the properties of the initial and final value and calculate the values of i(0) and i(∞).c)Find the expression for i(t). Check if the values of i(0) and i(∞) agree with those calculated in the previous item.d)Obtain voltages v1(t) and v2(t).
A hard disk drive (HDD) is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. Figure 1 shows a simplified block diagram of a HDD. For analysis purposes, given gain K=30 and G(s)=1 / s(s+4) determine the open-loop and closed loop poles of the HDD and plot these separately in the S-Plane. Also discuss the stability using two different approaches.
The switch in the circuit has been closed for along time before it is opened at t=0. Assume that the circuit parametersare such that the response is underdamped.1. Derive the expression for vo(t) as a function of Vg, α, ωd, C, and Rfor t≥0.2. Derive the expression for the value of t when the magnitude of vois maximum
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?