q7 70. Calculate the moment of inertia by direct integrationof a thin rod of mass Mand length Labout an axisthrough the rod at L/3, as shown below. Check youranswer with the parallel-axis theorem.L13- 2L/3-Axis Calculate the moment of inertia by direct integration of a thin rod of mass M and length L about an axis through the rod at L/3, asshown in the figure in Chapter 10, problem 70.A) 1/9 ML2(в) 2/7 ML?3/8 ML21/5 ML2

We are going to use parallel axis theorem here which states that I=Ic+Mr2 I:) moment of inertia…

'0. Calculate the moment of inertia by direct integration of a thin rod of mass Mand length Labout an axis through the rod at L/3, as shown below. Check your answer with the parallel-axis theorem. -L13 -2L/3- Axie

'0. Calculate the moment of inertia by direct integration of a thin rod of mass Mand length Labout an axis through the rod at L/3, as shown below. Check your answer with the parallel-axis theorem. -L13 -2L/3- Axie

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 70P: Calculate the moment of inertia by direct integration of a thin rod of mass M and length L about an...

See similar textbooks

Similar questions

Calculate the moment of inertia of a skater given the following information. (a) The 60.0-kg skater is approximated as a cylinder that has a 0.110-m radius. b) The skater with arms extended is approximated by a cylinder that is 52.5 kg, has a 0.110-m radius, and has two 0.900-m-long arms which are 3.75 kg each and extend straight out from the cylinder like rods rotated about their ends.
Figure OQ10.6 shows a system of four particles joined by light, rigid rods. Assume a = b and M is larger than m. About which of the coordinate axes does the system have (i) the smallest and (ii) the largest moment of inertia? (a) the x axis (b) the y axis (c) the z axis, (d) The moment of inertia is the same small value for two axes, (e) The moment of inertia is the same for all three axes.
Review. As shown in Figure P10.77, two blocks are connected by a string of negligible mass passing over a pulley of radius r= 0.250 m and moment of inertia I. The block on the frictionless incline is moving with a constant acceleration of magnitude a = 2.00 m/s2. From this information, we wish to find the moment of inertia of the pulley. (a) What analysis model is appropriate for the blocks? (b) What analysis model is appropriate for the pulley? (c) From the analysis model in part (a), find the tension T1(d) Similarly, find the tension T2. (e) From the analysis model in part (b), find a symbolic expression for the moment of inertia of the pulley in terms of the tensions T1 and T2. the pulley radius r, and the acceleration a. (f) Find the numerical value of the moment of inertia of the pulley.
Calculate the moment of inertia by direct integration of a thin rod of mass M and length L about an axis through the rod L/3 , as shown below. Check your answer with the parallel-axis theorem.
Rigid rods of negligible mass lying along the y axis connect three particles (Fig. P10.18). The system rotates about the x axis with an angular speed of 2.00 rad/s. Find (a) the moment of inertia about the x axis, (b) the total rotational kinetic energy evaluated from 12I2, (c) the tangential speed of each particle, and (d) the total kinetic energy evaluated from 12mivi2. (e) Compare the answers for kinetic energy in parts (b) and (d). Figure P10.18
A horizontal disk with moment of inertia I1 rotates with angular speed 1 about a vertical frictionless axle. A second horizontal disk having moment of inertia I2 drops onto the first, initially not rotating but sharing the same axis as the first disk. Because their surfaces are rough, the two disks eventually reach the same angular speed . The ratio /l is equal to (a) I1/I2 (b) I2/I1 (c) I1/( I1 + I2) (d) I2/( I1 + I2)
Four objects are held in position at the corners of a rectangle by light rods as shown in Figure P8.37. Find the moment of inertia of the system about (a) the x-axis, (b) they-axis, and (c) an axis through O and perpendicular to the page.
An approximate model for a ceiling fan consists of a cylindrical disk with four thin rods extending from the disks center, as in Figure P8.41. The disk has mass 2.50 kg and radius 0.200 m. Each rod has mass 0.850 kg and is 0.750 m long, (a) Find the ceiling fans moment of inertia about a vertical axis through the disks center, (b) Friction exerts a constant torque of magnitude 0.115 N m on the fan as it rotates. Find the magnitude of the constant torque provided by the fans motor if the fan starts from rest and takes 15.0 s and 18.5 full revolutions to reach its maximum speed. Figure P8.41
A disk with moment of inertia I1 rotates about a frictionless, vertical axle with angular speed i. A second disk, this one having moment of inertia I2 and initially not rotating, drops onto the first disk (Fig. P10.50). Because of friction between the surfaces, the two eventually reach the same angular speed f. (a) Calculate f. (b) Calculate the ratio of the final to the initial rotational energy. Figure P10.50
Three identical thin rods, each of length L and mass m, are welded perpendicular to one another as shown in Figure P10.43. The assembly is rotated about an axis that passes through the end of one rod and is parallel to another. Determine the moment of inertia of this structure about this axis.
A playground merry-go-round of radius R = 2.00 m has a moment of inertia I = 250 kg m2 and is rotating at 10.0 rev/min about a frictionless, vertical axle. Facing the axle, a 25.0-kg child hops onto the merry-go-round and manages to sit down on the edge. What is the new angular speed of the merry-go-round?
A horizontal disk with moment of inertia I1 rotates with angular speed 1 about a vertical frictionless axle. A second horizontal disk having moment of inertia I2 drops onto the first, initially not rotating but sharing the same axis as the first disk. Because their surfaces are rough, the two disks eventually reach the same angular speed . The ratio /l is equal to (a) I1/I2 (b) I2/I1 (c) I1/( I1 + I2) (d) I2/( I1 + I2)