0.4 Choose the correct anawer: 1-The maximum peak-to-peak ripple in output cumrent of step-down converter with RL load depands on (a) Supply voltage. (b) Inductunce of load. (e)Chopping frequency. (d)All of the above. 2-The formmala ofoutput voltage of boost converter in continuous conduction mode in: (a) = DV, (b)V = (e)V- (d)v-2D – 1), 3-The condition fior operation of buck converter in continuous conduction mode for a given V LDand T, is (a) The output current is less than boundary current. (b) The output curent is more than houndary current. (c) The uutput current is more er less than boundary current. (d)None of above 4-For the converier with supply voltage varied between 12V and 24V, the output voltage is regulated to value of 15V, the suitable DC-DC converter is: (a) Buck converter. (b)Boost comarter. (c) Buck-hoost converter. (d)Forwand converter.

0.4 Choose the correct anawer: 1-The maximum peak-to-peak ripple in output cumrent of step-down converter with RL load depands on (a) Supply voltage. (b) Inductunce of load. (e)Chopping frequency. (d)All of the above. 2-The formmala ofoutput voltage of boost converter in continuous conduction mode in: (a) = DV, (b)V = (e)V- (d)v-2D – 1), 3-The condition fior operation of buck converter in continuous conduction mode for a given V LDand T, is (a) The output current is less than boundary current. (b) The output curent is more than houndary current. (c) The uutput current is more er less than boundary current. (d)None of above 4-For the converier with supply voltage varied between 12V and 24V, the output voltage is regulated to value of 15V, the suitable DC-DC converter is: (a) Buck converter. (b)Boost comarter. (c) Buck-hoost converter. (d)Forwand converter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a buck converter with the controlled switch as MOSFET and the uncontrolled switch as diode, the input to buck converter is 60 V. The MOSFET is turned on and off for 20 msec and 10 msec periodically. Assuming ideal components, the output voltage of the buck converter is
c) A buck converter with constant frequency peak current mode control has Vs = 28V, V = 20V, L = 301uH, fs = 100 kHz. Find the ramp slop for the optimum compensation and the peak compensation voltage. %3D
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ?
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?
Draw the circuit diagram of DC to DC converter using switched capacitor.
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ? Please answer D;e;f
Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
the way of working for boost dc-to-dc converter.
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: R 2. vZ.1. Ir = Vo n. T +Yi, = I, E Select one: O a. 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ W
Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
Industrial Electronics If the given types of DC-DC Converter has an input voltage of 25V. The output voltage of each converter using a duty cycle of 0.4s. a.) Buck Converter Vout?b.) Boost Converter Vout?C.)Buck-boost converter Vout?