A lightweight lever consists of a 0.8m solid bar rigidly mounted to a large structure and a 0.5m solid lever welded to the solid bar. Using the loading indicated and assuming the material has a Young's Modulus of 200 GPa and a shear modulus of 86 GPa, calculate: (a) the maximum stress at Point A on the Cross-section a-a, (b) the vertical displacement of the knob when the load is applied relative to Cross-section a-a. D B 50 mm Section a-a 0.8 m 0.5 m 100 N 38 mm

A lightweight lever consists of a 0.8m solid bar rigidly mounted to a large structure and a 0.5m solid lever welded to the solid bar. Using the loading indicated and assuming the material has a Young's Modulus of 200 GPa and a shear modulus of 86 GPa, calculate: (a) the maximum stress at Point A on the Cross-section a-a, (b) the vertical displacement of the knob when the load is applied relative to Cross-section a-a. D B 50 mm Section a-a 0.8 m 0.5 m 100 N 38 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.
A timber column, 8 in. by 8 in. in cross section, is reinforced on all four sides by steel plates, each plate being 8 in. wide and t in. thick. Determine the smallest value of tfor which the column can support an axial load of 300 kips if the working stresses are 1200 psi for timber and 20 ksi for steel. The moduli of elasticity are 1.5 x106psi for timber and 29 x 106psi for steel.
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel tobe used, the maximum allowable stresses are σ =175 MPa, τ =100 MPa,and σb=350 MPa. Design the tie bar by determining the required values of(a) the diameter d of the bolt, (b) the dimension b at each end of the bar, and(c) the dimension h of the bar.
A lever ABC is pinned at C and attached to a 12-mm diameter control cable AD. a. If the allowable tensile stress in the control cable is 140 MPa, what is the maximum safe value of the load P applied as shown in the diagram? b. What is then the shearing stress developed in the 20-mm diameter pin support at C? c. What is the bearing stress between the pin and the 25-mm thick support plates at C?
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.
A rectangular piece of wood, 55 mm by 101 mm in cross-section is used as a compression block. The grain makes an angle of 20 degrees with the crosssection plane. Determine the maximum axial load (kN) that can be applied to the block if the allowable shearing parallel to the grain is 5 Mpa. What is the allowable compressive stress(Mpa) parallel to the grain if the failure on shearing and compression is to occur simultaneously?
Observe the figure that shows the assembly of the ACD arm, suspended by a bearingin C coupled to a horizontal rod in A. The arm supports a load of 4 kN applied at theend D. Considering that the allowable shear stress of the material of the pin in bearing C is30 MPa, what is the diameter of pin C, which supports the 4 kN load? What is theelongation of the steel bar AB (E= 200 GPa) with a diameter of 20 mm? BA length 300mm
A rectangular piece of wood, 50mm by 100mm in cross section, is used as a compression block shown. Determine the axial force P that can be safely applied to the block if the compressive stress in wood is limited to 25 MPa and the shearing stress parallel to the grain is limited to 10 MPa. The grain makes an angle of 20° with the horizontal, as shown.
A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 260 kN without exceeding an allowable stress of 240 MPa or stretching more than 10 mm.
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.
Two forces P can be applied separately or at the same time to a plate that is welded to a solid circular bar of radius r. Determine the largest compressive stress in the circular bar (a) when both forces are applied, (b) when only one of the forces is applied.